background image

C

Co

om

mp

plle

ette

ed

d  IIn

ns

stta

alllla

attiio

on

n

As you proceed with the assembly, installation and adjustment
procedures in this manual, you may find it helpful to refer back to
this illustration of a completed installation.

4

(1) 

Cable Pulley Bracket

(2)

Trolley

(3)

Chain/Cable Assembly

(4) 

Rail

(5) 

Hanging Bracket

(6)

Power Cord

(7) 

Opener

(8) 

Light Lens

(9) 

Manual Release
Rope & Handle

(10) 

Door Arm

(11)

Door Bracket 

(12)

Header Bracket

ASSEMBLY SECTION

Assemble Rail 

Place Rail pieces (1) on a flat surface for assembly. Take special note
of the raised line on the Rail pieces (4) these lines MUST line up in
order for the Rail to fit together properly. All three Rail sections are
interchangeable. Slide Rail Braces (2) into slots on the sides of Rail.
Make sure small tabs on Rail Braces (3) are up against top lip of Rail.
Connect Rail by sliding other end of braces into next Rail. Be sure the
raised lines that run down Rail sections (4) line up. Tap Rail assembly
(5) on a piece of wood (6) until Rail sections are flush. Repeat for final
Rail section.

5

Assemble Cable Pulley Bracket

Insert Carriage Bolt (1) though square hole in Cable Pulley Bracket (4).
Remove Chain/Cable assembly (3) from carton. Wrap Cable around
Cable Pulley (2) and insert Pulley into Bracket (

NOTE:

Make sure the

Bracket is assembled in position shown).

Slide pin (5) through holes in

Cable Pulley Bracket and Cable Pulley. 

NOTE: 

Trolley with Magnet (6)

MUST be installed in the position shown.

6

1

2

3

4

6

5

9

10

12

11

8

7

NOTICE

9

4

1

1

1

4

4

1

5

5

4

6

2

2

4

5

4

3

3

1

2

5

4

4

3

1

2

5

1

2

4

3

6

Insert Chain/Cable into Rail

Slide Cable Pulley Bracket (1) into Rail assembly (3), be sure to insert
Cable Pulley Bracket as shown. Push Cable Pulley Bracket toward
front of Rail and slide Inner Trolley (2) into Rail assembly. Magnet (4)
MUST be installed in position shown or unit will not function properly.

7

1

2

3

2

4

Attach Trolley to Rail 

Turn Rail assembly over. Slide Outer Trolley (1) into Rail assembly (2),
be sure the end with Door Arm Hole (3) is heading in direction of door
(4). Slide Outer Trolley down Rail until it engages with Inner Trolley.

8

1

2

1

3

4

4

Summary of Contents for Econolift ML500









Reviews: