Bandit
44
Copyright 5/18
MODEL 12XP/990
Consult your engine manual for proper break‑in procedures. Various engines require somewhat different
procedures, but basically the engines need to operate at lower R.P.M.’s and loads for a specific time.
Failure to properly break-in your engine may result in poor bearing and piston ring surfaces.
The Bandit has only been run for a short time to test proper hydraulic pressures, possible leaks, etc. The
fuel tank will be empty. Fuel is provided through a small auxiliary tank for testing. This immensely helps
maintain safety in our manufacturing facility and while shipping.
Do not let anyone operate or maintain this machine until they have thoroughly read this manual, reviewed
the equipment decals, watched the equipment video, and has been properly trained. You can purchase
additional Bandit manuals, decals and videos for a nominal fee.
Expensive damage to the Bandit will occur if proper preparation is not taken before welding on the machine.
Be sure to disconnect both battery cables and the engine ECM (engine control module) before welding. Follow
the specific Engine MFG. instructions for proper welding and grounding procedures, before attempting to weld
on the machine. If welding on the machine, do not ground the welder through the machine bearings, ground
near work to be performed.
MAINTENANCE
MAINTENANCE
The Bandit is a very simple machine to maintain. If you will follow a regular scheduled preventative
maintenance program, you should have years of trouble free operation.
DANGER
!
NOTICE
NOTICE
NOTICE
NOTICE
1.
Check the safety decals and engine gauges:
Replace any missing or damaged decals and/or
engine gauges.
2.
Check all safety equipment:
Check for proper operation. Repair or replace as
needed. With everything shut down and stopped,
ensure last chance cables freely operate feed
control valve.
3. Check entire machine for loose bolts, nuts,
parts, or components:
Check entire machine for any loose parts or
components. Check for loose nuts or bolts. Torque,
tighten, or replace any of the loose components. See
page 49 for specific bolt torques.
4. Check all guards:
Check to make sure all guards are in place and
installed correctly. Make sure they are secure.
5.
Check chipper hood hinge:
Make sure the hood hinge operates correctly, and is
lubricated. Must replace hinge if damaged.
6.
Checking for foreign objects:
Before opening the hood make sure the clutch is
disengaged, the engine off, the disc/drum lock pin
is installed, battery is disconnected, and also make
sure the ignition key is in your possession. Remove
the hood pin padlock, disconnect the chipper hood
engine disable plug, suppress the spring lock for
hood pin on disc chippers, and then remove the
hood lock pin. Look for any foreign objects inside
the chipper housing or in the knife pockets of the
disc/drum. Remove any foreign objects found.
7.
Check chipper drum assembly:
Check the condition of knife holder threads, secure
welds, torqued bolts, excessive wear and impact
cracks. If a problem is found contact the chipper
manufacturer or an authorized Bandit dealer. Also
check the chipper housing at this time. Check the
chipper base, belly band, and hoods for wear or
damage. Also inspect the chipper bearings.
DAILY START UP & MAINTENANCE
Before attempting any type of maintenance, disengage clutch, wait for the disc/drum to come to a complete
stop, turn off engine, remove the ignition key, make sure the ignition key is in your possession, install the
disc/drum lock pin, and disconnect the battery.
DANGER
!
Summary of Contents for INTIMIDATOR 12XP/990
