background image

 Accessories

Power Panel C70   User's manual V1.30 

97

6.2 TB6102 2-pin power supply connector

This 1-row 2-pin terminal block is used to connect the power supply.

6.2.1 Order data

Model number

Short description

Terminal blocks

0TB6102.2010-01

Accessory terminal block, 2-pin (3.81), screw clamp terminal block 1.5 mm²

0TB6102.2110-01

Accessory terminal block, 2-pin (3.81), cage clamp terminal block 1.5 mm²

Table 28: 0TB6102.2010-01, 0TB6102.2110-01 - Order data

6.2.2 Technical data

Information:

The following specifications, properties and limit values apply only to this accessory and may deviate

from those that apply to the complete system. The data specifications for the complete system take

precedence over those of individual components.
The technical data in this manual is current as of its creation/publication. We reserve the right to make

changes.

Model number

0TB6102.2010-01

0TB6102.2110-01

Terminal block

Number of pins

2 (female)

Type of terminal block

Screw clamp terminal block

Cage clamp terminal block

Cable type

Only copper wires (no aluminum wires!)

Spacing

3.81 mm

Connection cross section

AWG wire

28 to 16

Wire end sleeves with plastic covering

0.25 to 0.5 mm²

With wire end sleeves

0.25 to 1.5 mm²

Flexible

0.14 to 1.5 mm²

Inflexible

0.14 to 1.5 mm²

Tightening torque

0.22 to 0.25 Nm

-

Electrical properties

Nominal voltage

300 V

Nominal current 

1)

8 A

Table 29: 0TB6102.2010-01, 0TB6102.2110-01 - Technical data

1)

The limit data for each Power Panel must be taken into consideration.

Summary of Contents for VICPAS 4PPC70.0573-20B













































































































Reviews: