Banner DXM1200-X2 Instruction Manual Download

Page: 81 / 83

February 02, 2024

DXM1200-X2 Controller Instruction Manual

•
•
•

Continued from page 80

Model

Antenna Type

2.4 GHz Radio Module

Maximum Gain

Impedance

BWA-2O2-E

Omni, 1/4 wave dipole, Swivel

DX80-2400 or SX243

≤ 2 dBi

50 Ω

BWA-2O5-C

Omni, Collinear, Swivel

DX80-2400

≤ 5 dBi

50 Ω

BWA-2O5-MA

Omni, full-wave dipole, NMO

DX80-2400

≤ 4.5 dBi

50 Ω

BWA-2O6-A

Omni, Dome, Box Mount

DX80-2400

≤ 6 dBi

50 Ω

BWA-2O7-C

Omni, Coaxial Sleeve, Swivel

DX80-2400

≤ 7 dBi

50 Ω

Mexican Importer

Banner Engineering de Mèxico, S. de R.L. de C.V. | David Alfaro Siqueiros 103 Piso 2 Valle oriente | San Pedro Garza Garcia Nuevo Leòn, C. P. 66269

81 8363.2714

ANATEL

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas

devidamente autorizados.

Para maiores informações, consulte o site da ANATEL

www.gov.br/anatel/pt-br/

Warnings

WARNING:

Do not use this device for personnel protection

Using this device for personnel protection could result in serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A
device failure or malfunction can cause either an energized (on) or de-energized (off) output condition.

IMPORTANT:

Please download the complete

DXM1200-X2 Wireless Controller

technical documentation, available in multiple

languages, from www.bannerengineering.com for details on the proper use, applications, Warnings, and installation instructions of this

device.

IMPORTANT:

Por favor descargue desde www.bannerengineering.com toda la documentación técnica de los

DXM1200-X2 Wireless

Controller, disponibles en múltiples idiomas, para detalles del uso adecuado, aplicaciones, advertencias, y las instrucciones de

instalación de estos dispositivos.

IMPORTANT:

Veuillez télécharger la documentation technique complète des

DXM1200-X2 Wireless Controller

sur notre site

www.bannerengineering.com pour les détails sur leur utilisation correcte, les applications, les notes de sécurité et les instructions de

montage.

Install and properly ground a qualified surge suppressor when installing a remote antenna system.

Remote antenna configurations installed without surge

suppressors invalidate the manufacturer's warranty. Keep the ground wire as short as possible and make all ground connections to a single-point ground system
to ensure no ground loops are created. No surge suppressor can absorb all lightning strikes; do not touch the Sure Cross® device or any equipment connected

to the

Sure Cross®

device during a thunderstorm.

Exporting

Sure Cross®

Radios. It is our intent to fully comply with all national and regional regulations regarding radio frequency emissions.

Customers who want

to re-export this product to a country other than that to which it was sold must ensure the device is approved in the destination country.

The Sure Cross wireless

products were certified for use in these countries using the antenna that ships with the product. When using other antennas, verify you are not exceeding the

transmit power levels allowed by local governing agencies. This device has been designed to operate with the antennas listed on Banner Engineering’s website

and having a maximum gain of 9 dBm. Antennas not included in this list or having a gain greater than 9 dBm are strictly prohibited for use with this device. The
required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen such that the
equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. Consult with Banner Engineering Corp. if the
destination country is not on this list.