background image

P/N 128185 Rev A

Banner Engineering Corp. • Minneapolis, MN U.S.A.

www.bannerengineering.com  •  Tel: 763.544.3164

SureCross™ DX80 Quick Start Guide

9

Quick Start: 

STEP 5 

> Site Survey (optional)

Remove Gateway rotary switch access cover.

To check the status of Node 1, change the Gateway’s 
right rotary switch setting to 1

The Gateway is now enabled to read the status of 
Node 1; the display scrolls through the Node’s I/O 
status.

Single-click Gateway push button 1  

Device Information menu

Single-click Gateway push button 1

Factory Settings menu

Single-click Gateway push button 1

Site Survey menu

Single-click Gateway push button 2

Site Survey will be conducted with Node 1

Single-click Gateway push button 2

The Gateway analyzes the quality of the signal from 
the selected Node by counting the number of data 
packets it receives from the Node.
M = Percentage of missed packets
R = RED marginal signal
Y = YELLOW good signal
G = GREEN excellent signal
When possible, install all devices in positions that 
optimize the percentage of YELLOW and GREEN 
data packets received. 

Examine reception readings (M,R,Y,G) of the Gateway 
at various locations. Note that the numbers displayed 
are a percentage. M displays the percent of missed 
packets while R, Y, and G display the percent of 
received packets.

Double-click Gateway push button 2

End Site Survey

Change right rotary switch back to 0 (Gateway)

Change the device readings back to the Gateway

Double-click Gateway push button 2

Move back to the top level menu

Single-click Gateway push button 1

Return to RUN mode

Single-click Gateway push button 1

Single-click Gateway push button 1

Install Gateway rotary switch access cover.

Refer to the installation instructions to create an IP67 

seal.

A site survey analyzes the radio signal between a Gateway and a speci

fi

 ed Node and reports the number of data packets missed or received. 

Perform the Site Survey before permanently installing your network to ensure reliable communication. Use the Gateway to perform a site 
survey analysis.

SITE SUR

VEY

 MENU

SUR

VEY

 READINGS

RETURN 

TO

 RUN MODE

User Action

Display/Status

Notes

Summary of Contents for SureCross DX80

























Reviews: