Specifications
Supply Voltage
10 V to 30 V dc (10% maximum ripple)
Supply Current (Exclusive of Load Current)
< 25 mA at 15 V
< 40 mA at 24 V
Repeatability
100 µs
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Protection Circuitry
Protected against false pulse on power-up and continuous overload or
short-circuit of output
Output Configuration
Current sourcing (PNP) or current sinking (NPN), depending on model;
Light- or dark-operate selectable; Selectable 30 ms output OFF-delay
Rating: 100 mA max
Off-state leakage current: < 50 µA at 30 V
ON-state saturation voltage: < 1.5 V at 10 mA; < 3 V 100 mA
Output Response Time
Note: Momentary delay on power-up; output does not conduct during
this time
400 µs ON/OFF
Required Overcurrent Protection
WARNING: Electrical connections must be made
by qualified personnel in accordance with local
and national electrical codes and regulations.
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to
http://
www.bannerengineering.com
.
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
20
5.0
22
3.0
24
2.0
26
1.0
28
0.8
30
0.5
Emitter LED
Visible red, 625 nm
Indicators
Two LEDs (1 green, 1 amber)
Green solid: Indicates power applied and sensor ready
Green flashing: Indicates sensor operating in marginal state, in need of
reconfiguration
Amber solid: Indicates output conducting
Factory Default Settings
Setting
Factory Default
Sensing Mode
Dark Set
Output Logic
Dark Operate
Offset Percent
16%
Push Button
Unlocked
Auto Compensation
Disabled
OFF Delay
Disabled
Mounting Torque
Nose mount: 18 mm mounting nut, 20 lbf·in (2.3 N·m)
Side mount: Two M3 screws, 5 lbf·in (0.6 N·m)
Construction
ABS housing, PMMA window
Connections
PVC-jacketed 4-conductor 2 m (6.5 ft) or 9 m (30 ft) unterminated
cable, or 4-pin Euro-style or 4-pin Pico-style quick-disconnect (QD),
either integral or 150 mm (6 in) pigtail, are available. QD cordsets are
ordered separately.
Operating Conditions
Temperature: –40 °C to +70 °C (–40 °F to +158 °F)
Relative Humidity: 90% at +50 ºC (non-condensing)
Environmental
IEC IP67
Application Notes
If the push button does not appear to be responsive, perform the push
button enable procedure
Certifications
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp.
Copyright Notice
Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not
intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product
warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any
time. For the most recent version of any documentation, refer to:
www.bannerengineering.com
.
©
Banner Engineering Corp. All rights reserved.
WORLD-BEAM QS18 Clear Object Detection
www.bannerengineering.com - Tel: +1-763-544-3164
