background image

3/18

Designed for care

Introduction

Bano’s height-adjustable cisterns can be adjusted either manually with a crank or electrically. 

This lightens the carer’s work load because one person can quickly and easily adjust the 

height of the toilet to fit the users need. The height of the toilet can be adjusted 20cm.

The cistern is supplied either with a manual hand crank or with electrical height adjustment. 

With simple steps the height of the toilet and the WC grab bars can be adjusted. For 

bathrooms with external pipes an extension for the cistern must be used. For more 

information see Bano interface on www.bano.no

Electrical adjustment is operated by a button on the top of the cistern. For manual 

adjustment, use the accompanying crank.

Accessories

With external pipes, please use an extension (5970-22/5970-23), either 50 mm or 100 mm. 

Article numbers:

5965    

WC 530

5975    

WC 700

5985EC  

WC-bowl 530 mm EasyClean

5995EC  

WC-bowl 700 mm EasyClean

5920-BVT  Bano swivel toilet

5603    

Grab bars WC 900 mm (35 in.)

5604    

Grab bars WC 700 mm (28 in.)

5970-22  

Extension 50 mm

5970-23  

Extension 100 mm

5970-03  

Toilet seat, white

5970-06 

Toilet seat, grey

Compliance with the EU directive

This product is CE branded.

See also:

EN 12182: 2012: Assistive products for persons with disability

EN 14055: 2011: WC and urinal flushing cisterns

EN 997: 2013: Sanatary appliances, washbasins

Summary of Contents for 5970S3-EL



















Reviews: