90326 Banzai
3
safety area
10 ft (305 cm)
10 ft (305 cm)
WARNING:
Overfilling will cause damage to
your ball.
This product is intended to be used
as a toy and not as a personal
flotation device.
Inflate this product with AIR.
NOTE: For easy air inflation,
use a manual air pump
designed specifically for
plastic inflatables.
Heads up; try and catch that wave! Race down the water slide, and make a splash as
you land beside the water-spraying tidal wave wall. Heat up with a game of one-on-one
in the basketball center before cooling down in the roomy splash pool. With the
included continuous airflow blower, all of this fun inflates in under 2 minutes.
Heavy-duty Dura-Tech™ construction ensures lasting strength and durability. It’s like
having a beach in your own backyard!
PLACEMENTS: Use on flat lawn only, not pavement or other hard surfaces. Lawn
should be free of rocks, bumps, depressions, sticks, etc. The product should be set up
in a location that has a minimum distance of 10 ft (305 cm) from any freestanding
structures or obstructions, including houses, garages, fences, trees, playground
equipment and large rocks.
INTRODUCTION
SETUP INSTRUCTIONS
Fig. A2
Fig. A1
Fig. A3
Fig. A4
Fig. A5
Fig. A6
SETUP
1. Unfold the constant air inflatable and place in the desired position on a smooth and level surface.
2. Lay out the water hose assembly and match the number on each sprayer to the correct position on the arch of the
inflatable. Once the numbers are matched, attach the sprayers to the arch and corresponding position using the
Velcro straps provided. Secure the water tubing using the Velcro hooks & loops located on top of the arch, and
along the side of the inflatable. (Fig A1-A3)
3. Attach the long intake tube at the back of the inflatable to the mouth of the blower motor using the attached Velcro
Strap. To ensure a secure fit, wrap the strap around
the mouth of the blower and tightly attach the
self-sticking strap. (Fig A4-A6)
4. Use the drawstrings to tie shut the short air release
tube along the back of the constant air
inflatable.(Fig A7)
5. Position the blower in a straight line perpendicular
and level to the back of the inflatable. The blower
should be placed on a stable surface and remain upright after the inflatable is inflated. The blower is a
high-volume fan capable of moving a lot of air very quickly. Place the blower in an area where it will not suck in dirt
or leaves. Keep blower away from children, water and moving vehicles. Set up the inflatable far away from any
structures or obstructions. Once positioned, secure the blower with the blower ground stakes provided. (Fig A8)
6. Do not set up over concrete, asphalt, packed earth, or any other hard surfaces. A fall onto a hard surface can
result in serious injury.
7. Locate the loops around the bottom of the inflatable and anchor them to the turf, sand soil or rock soil with the
water slide ground stakes provided. (Fig A9)
8. Ground stakes must be completely inserted into the ground so that no part of the stake is protruding above the
ground surface. This will help prevent tripping or injuries resulting from a fall.
9. Plug the blower into a properly grounded outlet and turn it on. The inflatable should inflate in under 2 minutes. Do
not allow children to use the inflatable until it is fully inflated.
10. Close the water valve at the bottom of the pool. (Fig A10)
11. Fill the pool with at least 8 in (20 cm) of water before playing. Thoroughly wet all slide surfaces, platforms and
climbing walls before use to ensure optimal play performance.
12. Do not fill the product tub to more than the maximum fill line marked inside the pool wall.
13. After inflation, the blower should run continuously while children are playing.
FOR INFLATABLE BASKETBALL:
14. Roll out the ball. Inspect for holes, tears or other damage. (Fig A11)
15. Inflate this product with AIR. (Fig A12)
NOTE: For easy air inflation, use a manual air pump designed specifically for plastic inflatables.
BY MOUTH: Remove the air valve plug and squeeze the base of the valve causing the inner flap to open for
inflation.
BY PUMP: Remove the air valve plug and insert air pump nozzle into the valve. The air pump nozzle should be
inserted deep enough to open the inner valve flap.
Do not over inflate the item. Once the item is completely inflated, then insert the air valve plug to seal it shut.
NOTE: Fill inflatable with air until it is firm and solid. If there is any straining at the seams, the item is over inflated.
If any seam begins to strain, immediately stop inflation and release air to reduce the pressure until all signs of
stress on the inflatable are gone. DO NOT use the inflatable if there is straining at the seams. Use of an
over-inflated item may result in serious injury, paralysis or death.
Inspect this product for rips, tears or punctures. Do not use if damaged.
OR
OR
Fig. A12
Fig. A7
Fig. A8
Fig. A9
Fig. A10
Fig. A11
