background image

Baracuda

®

 Adventura™ Robotic Pool Cleaner | Owner's Manual

7. 

Push and position the rib of the inner 
side of the tire in the groove of the wheel 
(Figure 33). If needed, turn the wheel 
gently to help with installation.

Figure 33.  Push the Tire into Place on the Wheel

Section 6. Troubleshooting

6.1  Using the Information LED

The information LED 

 on the Control box 

flashes in a specific sequence to indicate one of  
three possible cleaner malfunctions.

LED Flashing

Cause

Solution

1 Flash 
LED flashes once

Floating cable may not be 
plugged into the Control box 
correctly.

Unplug the floating cable from the Control box and 
reconnect.
If the problem persists, contact Baracuda Customer 
Service at  1300 784 423

2 Flashes 
LED flashes twice

Cleaner wheels may be jammed 
or brushes may be blocked with 
debris.

Turn cleaner wheels to ensure they are not jammed.
Check brushes for debris.
Start a new cleaning cycle.
If the problem persists, contact Baracuda Customer 
Service at  1300 784 423.

3 Flashes  
LED flashes three

Pump axis or propeller may be 
jammed with debris. 
 
Dirty filter.

Check the pump axis for debris.
Check propeller for debris.
Clean the filter.
Start a new cleaning cycle.
If the problem persists, contact Baracuda Customer 
Service at 1300 784 423.

 13

Summary of Contents for Captura EM14 Series

















Reviews: