background image

SETTE™ 270 MANUAL

v2.1 August 27, 2019

3

SAFETY INFORMATION

Please read the information below very carefully. It contains 
important safety information for this appliance. Please keep 
these instructions for future reference.

CAUTION: ALWAYS unplug the electrical supply cord prior to cleaning the grinder.

 !

Use only with AC current and the correct voltage. See the 
label on the base of the grinder to determine the correct 
voltage.

 !

Only clean the grinder housing with a dry or slightly damp 
cloth. Do not immerse the grinder, plug or cord in water or 
any other liquid.

 !

Baratza will not accept any liability for damage, injury, or 
warranty if the grinder is used other than for its intended 
purpose (i.e. grinding roasted whole coffee beans) or is 
improperly operated or repaired.

 !

This appliance can be used by children aged from 8 
years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience 
and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe way 
and understand the hazards involved.

 !

If the supply cord is damaged, it must be replaced by 

the manufacturer, its service agent or similarly qualified 

persons in order to avoid a hazard.

 !

Always unplug the electrical supply cord before 
assembling, disassembling or cleaning the grinder.

 !

To unplug, grasp plug and remove from the outlet.  
Never pull on the cord.

 !

Keep the appliance and its cord out of reach of children 
aged less than 8 years.

 !

Do not leave your grinder unattended while turned ON.

 !

Cleaning and user maintenance shall not be done  
by children without supervision.

 !

Do not operate the grinder with a damaged cord or plug. 

Summary of Contents for sette 270














Reviews: