6. CSE-200 Configurator
3. To change the IP address or subnet mask, click in the input
fi
eld and enter the 4 octets of the new IP address or subnet mask.
Note:
This must NOT be 0.0.0.0 for static IP-Address assignment.
Frequency band & channel
1. Select the wireless connection channel by clicking on the drop down box and selecting the desired channel.
The channels available in the list vary according to the regional version of your Base Unit. Re-pairing the Buttons is not required
when changing the frequency band or wireless connection channel.
2. Select the wireless connection frequency band: 2.4 GHz or 5 GHz by clicking on the drop down box and selecting the correct
band.
Note:
Make sure your PC’s wireless interface supports the 5 GHz band before selecting it on the Base Unit.
SSID & passphrase
1. Enter a public name (SSID) for the wireless network.
The default SSID is
ClickShare-<serial number Base Unit>
.
2. If you want to broadcast this SSID, check the checkbox before
Enable SSID broadcast
.
3. Enter a new WiFi passphrase and con
fi
rm that passphrase.
Signal strength
1. Select the Signal Strength. Click on the slider and reduce the broadcasted power (signal strength) until the desired strength is
obtained.
Note:
Too low power and interference by others might lead to connection issues. If so, increase again the signal strength until
the issues are solved.
By default the strength is set to 100%.
WebUI access via Wi-Fi
1. To allow access to the con
fi
gurator via Wi-Fi, check the check box in front of
WebUI available via Wi-Fi
.
Checked: Con
fi
gurator accessible via Wi-Fi.
Not checked: access to the con
fi
gurator via Wi-Fi is blocked.
6.11 LAN settings
About LAN network settings
A network connection can be con
fi
gured through DHCP or by manually entering a
fi
xed IP address.
DHCP
Dynamic host con
fi
guration protocol. DHCP is a communications protocol that lets network administrators manage
centrally and automate the assignment of IP addresses in an organization’s network. Using the Internet Protocol, each
machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users
with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address
must be entered manually at each computer and, if computers move to another location in another part of the network,
a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from
a central point and automatically sends a new IP address when a computer is plugged into a different place in the
network.
Hostname & method
1. Log in to the
Con
fi
gurator
.
2. Click
Wi-Fi & Network
→
LAN Settings
.
40
R5900023 CLICKSHARE CSE-200 13/07/2016
Summary of Contents for ClickShare CSE-200
