1. Safety
1.2
Important safety instructions
To prevent risk, personal injury and E2 damage
Please read this chapter carefully. It contains important information to prevent personal injury while installing the E2. Furthermore, it
includes several cautions to prevent damage to the E2. Ensure that you understand and follow all safety guidelines, safety instruc-
tions and warnings mentioned in this chapter before installing the E2. After this chapter, additional “warnings” and “cautions” are
given depending on the installation procedure. Read and follow these “warnings” and “cautions” as well.
•
Read these instructions.
•
Keep these instructions.
•
Heed all warnings.
•
Follow all instructions.
•
Only trained technicians may install the E2.
•
Installation of the E2 must be done in a dust free area.
•
Only use attachments/accessories speci
fi
ed by the manufacturer.
•
CAUTION: Troubleshooting must be performed by a trained technician. To reduce the risk of electrical shock, do not attempt
to service this equipment unless you are quali
fi
ed to do so.
•
Refer all servicing to quali
fi
ed service personnel. Servicing is required when the system has been damaged in any way, such
as liquid has been spilled or objects have fallen into the system, or the system has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•
FRAGILE: The E2 is fragile. Handle the E2 with care at all times.
•
To prevent injury, take note: by law, minimum 2 persons are required to carry the E2.
•
Do not remove covers or panels during normal operation. Removal of the top cover will expose dangerous voltages. To avoid
personal injury, do not remove the top cover. Do not operate the unit without the cover installed.
•
During maintenance operations, always switch off the E2 and unplug power cords before removing one of the covers, unless
otherwise stated.
•
Always wear a wrist band which is connected to the ground while handling the ESD sensitive parts.
•
Wear insulating gloves during the execution of the installation and maintenance actions to avoid short-circuit.
•
Be careful never to drop anything into the E2 assembly during the procedure. The fall of a tool or a spare part in the E2 could
have catastrophic consequences when you will restart the system.
•
Be careful to always follow strict procedures during maintenance operations (spare parts replacement).
•
This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply con-
ductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the
power cord is essential for safe operation.
•
This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord
into a properly wired receptacle before connecting to the product input or output terminals. A protective-ground connection by
way of the grounding conductor in the power cord is essential for safe operation.
•
Use only the power cord and connector speci
fi
ed for your product. Use only a power cord that is in good condition. Refer cord
and connector changes to quali
fi
ed service personnel.
•
To avoid
fi
re hazard, use only the fuse having identical type, voltage rating, and current rating characteristics. Refer fuse re-
placement to quali
fi
ed service personnel.
•
Replace spare parts only with the same or equivalent type recommended by the manufacturer.
•
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
•
Rated maximum ambient operating temperature, t
a
= 40°C (104°F).
•
To avoid explosion, do not operate this product in an explosive atmosphere.
R5905947 E2 09/03/2018
3
Summary of Contents for Event Master E2
