17
16
Preparations
Others
Opreation
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Attaching the Fluorescent Lamps
Attach the supplied fluorescent lamps to the lamp holders on the light arms.
Check that the POWER switch is in the OFF position, and the power plug is disconnected from the AC outlet.
PREPARATIONS
2
While pressing the lamp towards the socket, fit it in the holder.
A clicking sound is heard.
When replacing the lamp, see “Replacing the fluorescent lamps”. (
☞
p.38)
Note
[
Be careful that the lamp will not be damaged by the holder.
[
Make sure that the lamp is firmly secured in the socket and holder.
1
Insert the fluorescent lamp into the socket of the light stand.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Connecting the Power Cord
Connect the power cable after all other connections are completed.
First connect the cable to the AC input connector of this unit, next connect the ground wire, then connect it to an AC outlet.
Socket
If no clicking sound is heard,
press the holder with your fingers.
Caution
[
When handling a fluorescent lamp, avoid excessive force. Otherwise, the lamp may break,
causing injury.
Do NOT
force
Remove the cap from the
camera.
4
PREPARATIONS
To Fold the Camera
Arm and Light
Stands
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Reverse the procedure of “Raising the camera arm and
light stands”. (
☞
p.15)
4
Fold the light stands.
Fold the light stands with the fluorescent lamps
facing the document stage.
Fold the right stand first.
Then, fold the left stand.
5
While holding the stopper
pressed, fold the camera
arm until a clicking sound is
heard.
2
Draw in the camera arm.
3
While holding the stopper
pressed, raise the camera
arm until it stands vertically.
Grip the camera arm when raising the camera
head.
Note
[
Keep holding the camera arm and light stands until the folding process is complete.
1
Align the camera head with
the camera arm.
Caution
[
Do NOT apply excessive force to the camera arm and light stands. The unit may fall,
causing injury.
[
When operating (to raise or fold) the camera arm or light stands, be careful that your
hands and clothing are not caught by moving sections. This may cause injury.
[
Before use, confirm that the camera arm and camera head are locked in the shooting
position. If not, the camera arm may fall down, causing injury.
[
Do NOT lift the Imager by grasping the camera arm. Doing so may damage the Imager,
and it could lead to personal injury if the Imager falls.
Operate
with care
Raising the Camera Head and
Light Arms
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Continued
Power cable (supplied)
The shape of the cable may vary
depending on the country of sale.
**BARCO 012-017(E)
2000.7.18, 8:18 PM
16-17
