background image

8-2

Random  Access Adjustment Mode

5975948 RETRODATA 2100 210198

The following file manipulations are possible :

- Load :

 installation of a file for a new source.

- Edit :

 editing a loaded file to the source specs.

- Rename :

 renaming a file.

- Copy :

 copying a file to a new file.

- Delete :

  deleting an existing file.

- Options 

: way of displaying the file annotation and sort

possibilities.

Highlight 

File Service

 by pushing the control disc forwards or

backwards and press 

ENTER

 to select. The File service menu will

be displayed.

If the displayed image is not yet as it has to be, select the most

corresponding file and go to the Edit menu to change the file settings.

Press the control disc forwards or backwards to select the most

fitting file and press 

ENTER

 to select.

When scrolling through the files, the image will be adapted accord-

ing the settings of the selected file (on line adaptation).  When the

best fitting image is displayed, press 

ENTER

 to select this file.  A

confirm Load file menu will be displayed with the new created file

and the on which the new file is based on.

Press 

ENTER

 to confirm your new creations or 

EXIT

 to return to the

load file menu.

"All" : all files that can be loaded will be displayed.

"Fit" : only the best fitting files will  be displayed (with a distinction

of ± 2 lines and line duration distinction of ± 300 ns)

This filter can be "Fit" or "All".  To change the filter, press the control

disc to the right to select  "filter list" (filter list will be high lighted) and

press 

ENTER

 to toggle the annotation between brackets.

Load file

Press the control disc forwards or backwards to select LOAD and

press 

ENTER

 to display the Load menu.

The Load menu displays the corresponding files depending on the

installed filter.

During a load file, the actual active file is displayed next to the

indication 'Active file'.

ENTER

 displays the File Service menu;

EXIT

 returns to the Path selection menu.

ADJUST

 returns to operational mode.

Select with 

ê

 or 

é

then <ENTER>

Select with 

ê

 or 

é

then <ENTER>

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

OPTIONS

RANDOM ACCESS

ADJUSTMENT MODE

FILE SERVICE

PICTURE TUNING

AUDIO TUNING

GEOMETRY

LOAD FILE

FILTER LIST [All]

Filename

Src

Resolution

-----------------------------------------------------

ntsc.s01

1

675x240i

ntsc.c01

1

675x240i

ntsc_2.s01

1

675x240i

-----------------------------------------------------

Active file : ntsc.c50

Select with  

ê

 or 

é

ç

<ENTER> to accept

<EXIT> to return.

CONFIRM

LOAD FILE

Create file

ntsc.c02

based on file

ntsc.s01?

<ENTER> to confirm

<EXIT> to return

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

OPTIONS

Select with 

ê

 or 

é

then <ENTER>

<EXIT> to return.

File annotation :

xxxxXxxxx : active pixel rating

x : source number

xxx : file extension, first character is C (for custom made

files) or S (for standard files).

The second and third character is used for a following

number (=file index)

file index for custom files : 00 to 63.

xxxxxxxx.xxx  x  xxxxXxxxxi

xxxxxxxx : base name,  8 characters.

i or blank : i = interlaced, blank = not

interlaced

File Service

Before using a new source, a correct file has to be installed.  The

projector's memory contains a list of files corresponding to the most

used sources.  When the new source corresponds with one of

these files, the file can be loaded and saved for future use.  When

there is a little difference, the file can also be loaded and than edited

until the source specs are reached.

Summary of Contents for R9001300























































Reviews: