R5975059A BARCOVISION 708 200498
CONTROLLING
CONTROLLING
R5975059A BARCOVISION 708 200498
CONTROLLING
CONTROLLING
5-5
5-5
Projector address
a. hardware set up of the projector address.
Every projector requires an individual address between 0 and 16 which is set with
hardware DIP switches inside the projector. To change that address, contact a
BARCO authorized technician.
b. How to control the projector.
The projector's address may be set to any value between 0 and 16. When the address
is set, the projector can be controlled now with :
- the RCU for addresses between 0 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between
0 and 16 (only when the optional RS232 communication port is installed)
Note : a projector will respond to an RCU set to an address of '0' regardless of what
address is set in the projector itself.
c. Using the RCU.
Before using the RCU, it is necessary to enter the projector address into the RCU (only
when that address is between 1 and 9). The projector with the corresponding
address will listen to that specific RCU.
When address 0, 'zero address' is programmed into the RCU, every projector, without
exception will listen to the commands given by this RCU.
How to display a projector address?
Press the ADDRESS key (recessed
key on the RCU) with a pencil.
The projector's address will be
displayed in a 'Text box'. This text
box disappears after a few sec-
onds.
To continue using your RCU, it is
necessary to enter an address
with the digit buttons (address be-
tween 0 and 9). For example : if the
Address key displays projector
address 003, the press "3" digit
button on the RCU to set the RCU's
address to match the projector's
address. Do not press digit 003.
This will address the remote to '0'
and control all projectors in the
room.
PROJECTOR
ADDRESS
001
Projector address
a. hardware set up of the projector address.
Every projector requires an individual address between 0 and 16 which is set with
hardware DIP switches inside the projector. To change that address, contact a
BARCO authorized technician.
b. How to control the projector.
The projector's address may be set to any value between 0 and 16. When the address
is set, the projector can be controlled now with :
- the RCU for addresses between 0 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between
0 and 16 (only when the optional RS232 communication port is installed)
Note : a projector will respond to an RCU set to an address of '0' regardless of what
address is set in the projector itself.
c. Using the RCU.
Before using the RCU, it is necessary to enter the projector address into the RCU (only
when that address is between 1 and 9). The projector with the corresponding
address will listen to that specific RCU.
When address 0, 'zero address' is programmed into the RCU, every projector, without
exception will listen to the commands given by this RCU.
How to display a projector address?
Press the ADDRESS key (recessed
key on the RCU) with a pencil.
The projector's address will be
displayed in a 'Text box'. This text
box disappears after a few sec-
onds.
To continue using your RCU, it is
necessary to enter an address
with the digit buttons (address be-
tween 0 and 9). For example : if the
Address key displays projector
address 003, the press "3" digit
button on the RCU to set the RCU's
address to match the projector's
address. Do not press digit 003.
This will address the remote to '0'
and control all projectors in the
room.
PROJECTOR
ADDRESS
001
Summary of Contents for R9002327
