4. Web Management
The network con
fi
guration of WiPG-1000 is automatic via DHCP.
The default setting of the WiPG-1000 is DHCP client. When the WiPG-1000 is connected to a LAN that already
has a DHCP server present, the WiPG-1000 takes an IP address assigned to it by the server. When the WiPG-
1000 is connected to a LAN that does not have a DHCP server, the WiPG-1000 can become the DHCP server
in the network.
•
< IP Setup>
-
You can select “obtain an IP address automatically” or “Use the following IP address”.
-
IP Address:
The default value is 192.168.100.10.
-
Subnet Mask:
The default value is 255.255.255.0.
-
Default Gateway:
The default value is 192.168.100.10.
-
DNS Server:
The default value is 192.168.100.10.
•
< DHCP Server Setup >
-
You can select “Auto” (Enable/Disable the DHCP Server) or “Disable”.
-
Start IP:
The start IP address of the DHCP Server.
-
End IP:
The end IP address of the DHCP Server.
-
Subnet Mask:
The default value is 255.255.255.0.
-
Default Gateway:
The default value is 192.168.100.10.
-
DNS Server:
The default value is 192.168.100.10.
•
< Wireless Setup >
-
Wireless LAN:
The default value is “Enable.”
-
Host Name and Domain Name:
The default name is “WiPG-1000-xxx” (where xxx are the last three numbers of the MAC
ID shown on the bottom side of the WiPG-1000).
-
SSID Broadcast:
The default value is “Enable.”
-
Band:
The default value is “2.4 GHz.” (The “5 GHz” option is available in some regions.)
-
802.11 mode:
The default value is “2.4G B/G/N mixed.”
-
Channel:
The default value is “Auto.” (You can also choose to set a
fi
xed channel.) The “Auto” option means that after the
WiPG-1000 is powered on, the system scans all the wireless channels and selects a clear channel automatically.
-
Encryption:
The default value is “Disable.” (You can also choose “WEP,” “WPA,” or “WPA2.”)
-
Key:
If the “Encryption” function is enabled, you have to set a key value according to the encryption mode you selected.
-
Channel Bandwidth:
“20MHz” or “Auto” (20MHz/40MHz) [The default value is “Auto.”]
•
< AP Client >
-
Connect to Existing AP:
The default value is “Disable.” (If you choose “Enable,” input the SSID of the existing AP to which
you want to connect.)
-
Encryption:
The default value is “Disable.” (If you choose enable the “Connect to Existing AP” function, you can select
“WEP,” “WPA AES,” “WPA2 AES,” “WPA TKIP,” or “WPA2 TKIP.”)
-
Key:
If the “Encryption” function is enabled, you have to set the “Key” value according to the encryption mode you selected.
R5906158 WEPRESENT WIPG-1000 31/01/2018
17
Summary of Contents for WePresent WiPG-1000
