background image

Manual 2100-319F
Page

8 of 10

INSTALLATION WITH 16" THICK WALLS

When an application is required on a building with 16" wall,
a Wall Sleeve model number QWS48A-16 is required.

The installation of the QWS48A-16 is similar to the
QWS48A with one exception.  A condenser fill plate is
supplied with QWS48A-16, and is to be attached to the top
of the outdoor coil housing on the QT

EC

 unit.  See Figure 6.

To attach fill plate, remove the three screws on top of coil
section, place condenser fill plate and secure with the three
screws.

INSTALLATION WITH 19" THICK WALLS

When an application is required on a building with 19" wall,
a Wall Sleeve model number QWS48A-19 is required.

The installation of the QWS48A-19 is similar to the
QWS48A with one exception.  A condenser fill plate is
supplied with QWS48A-19, and is to be attached to the top
of the outdoor coil housing on the QT

EC

 unit.  See Figure 6.

To attach fill plate, remove the three screws on top of coil
section, place condenser fill plate and secure with the three
screws.

INSTALLATION WITH 23" THICK WALLS

When an application is required on a building with 23" wall,
a Wall Sleeve model number QWS48A-23 is required.

The installation of the QWS48A-23 is similar to the
QWS48A with one exception.  A condenser fill plate is
supplied with QWS48A-23, and is to be attached  to the top
of the outdoor coil housing on the QT

EC

 unit.  See Figure 6.

To attach fill plate, remove the three screws on top of coil
section, place condenser fill plate and secure with the three
screws.

INSTALLATION WITH 30" THICK WALLS

When an application is required on a building with 30" wall,
a Wall Sleeve model number QWS48A-30 is required.

The installation of the QWS48A-30 is similar to the
QWS48A with one exception.  A condenser fill plate is
supplied with QWS48A-30, and is to be attached  to the top
of the outdoor coil housing on the QT

EC

 unit.  See Figure 6.

To attach fill plate, remove the three screws on top of coil
section, place condenser fill plate and secure with the three
screws.

FIGURE  6

INSTALLATION OF CONDENSER FILL PLATE IN QWS48A-16, QWS48A-19, QWS48-23, QWS48-30 APPLICATION

SCREW

CONDENSER
FILL PLATE

SEAL

CONDENSER
FILL PLATE

Summary of Contents for QWS48A QWS48A-16











Reviews: