background image

  

Widening the Stereo Field

 

We generally recommend angling the speaker axes in towards the listening position to create an 
equilateral triangle as described above.  This yields the most accurate high frequency response and the 
sharpest stereo image at the center listening position.  In some cases, however, the listener might 
change positions frequently.  Or there might be multiple listeners.  In such situations it may be 
desirable to have a wider and less focused stereo field which provides better coverage over a range of 
listening positons.  This can be achieved by aiming the speaker axes more forward such that the axes 
cross further behind the center listening position.  The figure below illustrates the  general principle 
and is not meant to be an exact measure of speaker angles or optimal listening positions.  

Since the MicroMain26 has such wide off-axis dispersion,  the angle relative to the listener can be 
changed by up to 10 degrees with less than 1 dB variance in the frequency response across the audible 
spectrum.  Angling the speakers forward in this manner will somewhat defocus the center stereo 
image while providing generally better imaging over a range of listening positions.  For some users this 
may be an acceptable compromise.      

Summary of Contents for MicroMain26
























Reviews: