Bareknuckle Welterweight - Airless Paint Sprayer
OPERATING INSTRUCTIONS & SAFETY MANUAL
Bareknuckle Welterweight - Airless Paint Sprayer
OPERATING INSTRUCTIONS & SAFETY MANUAL
|
16 |
17
Clean Sprayer immediately to prevent permanent damage.
17
17
17
17
17
17
17
17
17
18
Grounding and Electric Requirements
Grounding Instructions
This product must be grounded.
In the event of an eletrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding
wire with an appropriate grounding plug . The plug must be plugged into an outlet that is properly installed and
grounded in accordance with all local codes and orinances.
Improper installation of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the green grounding wire to either flat blade
terminal. The wire with insulation having a green outer surface with or without yellow stripes is the grounding wire
and must be connected to the grounding pin. Check with a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt as to whether the product is properly grounded. Do
not modify the plug provided. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrican.
The sprayer cord includes
a grounding wire with an appropriate grounding contact.
Never use an outlet that is not grounded or an adapter.
Do not use the sprayer if the electrical cord has a damaged ground contact. Only use an extension cord with
an undamaged ground contact.
Warning!
The Plug According to the state!
The sprayer requires for type 470:
220-240Vac, 50Hz,11A, 1 phase,
circuit with a grounding receptacle.
18
Grounding and Electric Requirements
Grounding Instructions
This product must be grounded.
In the event of an eletrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding
wire with an appropriate grounding plug . The plug must be plugged into an outlet that is properly installed and
grounded in accordance with all local codes and orinances.
Improper installation of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the green grounding wire to either flat blade
terminal. The wire with insulation having a green outer surface with or without yellow stripes is the grounding wire
and must be connected to the grounding pin. Check with a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt as to whether the product is properly grounded. Do
not modify the plug provided. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrican.
The sprayer cord includes
a grounding wire with an appropriate grounding contact.
Never use an outlet that is not grounded or an adapter.
Do not use the sprayer if the electrical cord has a damaged ground contact. Only use an extension cord with
an undamaged ground contact.
Warning!
The Plug According to the state!
The sprayer requires for type 470:
220-240Vac, 50Hz,11A, 1 phase,
circuit with a grounding receptacle.
GROUNDING AND ELECTRICAL REQUIREMENTS
!
!
Grounding Instructions
LONG TERM STORAGE
When cleaning for long term storage (more than 48 hours).
It is very important that the Paint Sprayer is not stored with any water
or water-based material left in the Pump, Hose, Tubes, or Spray Gun.
This will corrode the product.
IMPORTANT: Clean the Sprayer before storage. See
“Cleaning”on pages 14-15.
1. Remove paint hose if not already removed.
2. Turn the unit over and loosen the Clamps
from both Tubes, then disconnect Tubes
from the Pump Body.
3. Add one ounce of light household oil or a
pump storage product into each inlet.
4. Turn Prime/Spray switch to Spray.
6. Hold a rag over the paint hose outlet.
5. Turn Pressure Control Knob to Low/Spray.
7. Switch Power to ON for five seconds, then
turn the power OFF.
8. Turn Prime/Spray switch to Prime, this will
keep storage fluids in sprayer.
9. Replace the Tubes and secure with the Clamps.
10. Wipe the sprayer with a clean cloth. Store in a clean dry location out of reach of children.
Returns not accepted & warranty void if sprayer is
not properly cleaned immediately after every use.
This product must be grounded.
In the event of
an electrical short circuit, grounding reduces the
risk of electric shock by providing an escape wire
for the electric current. This product is equipped
with a cord having a grounding wire with an
appropriate grounding plug . The plug must be
plugged into an outlet that is properly installed
and grounded in accordance with all local codes
and ordinances.
Improper installation of the grounding plug can
result in a risk of electric shock.
If repair or replacement of the cord or plug is
necessary, do not connect the green grounding
wire to either flat blade terminal. The wire with
insulation having a green outer surface with
or without yellow stripes is the grounding wire
and must be connected to the grounding pin.
Check with a qualified electrician or serviceman
if the grounding instructions are not completely
understood, or if you are in doubt as to whether
the product is properly grounded. Do not modify
the plug provided. If the plug will not fit the
outlet, have the proper outlet installed by a
qualified electrician.
The sprayer cord includes a grounding wire with an appropriate grounding contact.
The sprayer requires for type 470:
220-240Vac, 50Hz,11A, 1 phase, circuit
with a grounding receptacle.
Never use an outlet that is not grounded
or an adapter.
Do not use the sprayer if the electrical cord has a
damaged ground contact. Only use an extension
cord with an undamaged ground contact.
