background image

Bareknuckle Welterweight - Airless Paint Sprayer     

OPERATING INSTRUCTIONS  & SAFETY MANUAL

Bareknuckle Welterweight - Airless Paint Sprayer     

OPERATING INSTRUCTIONS  & SAFETY MANUAL   

  |  

6   |

Clean Sprayer immediately to prevent permanent damage.

Clean Sprayer immediately to prevent permanent damage.

 

INSTALLATION: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BEFORE YOU BEGIN

Familiarise yourself with the Paint Sprayer and it’s functions. 

Prime/Spray Switch

This switch toggles the unit between 

priming mode and spraying mode.

Trigger Lock

When engaged, this mechanism 

prevents the trigger from being 

pulled accidentally such as if the 

gun is dropped.

Lock whenever not in use.

Nozzle

The nozzle is reversible and 

removable to make cleaning and 

unclogging easier.
Turn to Spray (     ) position to use 

the spray gun.
Turn to Clean (Eject) position to 

clean the nozzle.

Pressure Control Knob

The Pressure Control Knob can be adjusted for High Pressure Spraying, 

Low Pressure Spraying , Priming/Cleaning, or Rolling. Align the Pressure 

Control Knob with indicator on the Sprayer Housing to set the function.

High Pressure Spray

Low Pressure Spray

Rolling

Prime/Clean

Returns not accepted & warranty void if sprayer is 

not properly cleaned immediately after every use.

Returns not accepted & warranty void if sprayer is 

not properly cleaned immediately after every use.

Summary of Contents for Welterweight APS
















Reviews: