background image

Bareknuckle Welterweight - Airless Paint Sprayer     

OPERATING INSTRUCTIONS  & SAFETY MANUAL

Bareknuckle Welterweight - Airless Paint Sprayer     

OPERATING INSTRUCTIONS  & SAFETY MANUAL   

  |  

10   |

11 

Clean Sprayer immediately to prevent permanent damage.

Clean Sprayer immediately to prevent permanent damage.

 

12 

 

 

 

 

12 

 

 

 

 

12 

 

 

 

 

12 

 

 

 

 

12 

 

 

 

 

12 

 

 

 

PRIMING SPRAY GUN

PRIMING AND STARTUP STEPS

This procedure is used for first time operation and also to flush 

storage fluids out of the Sprayer.

Priming Water-Based vs. Oil-Based Paints

Oil-based Paint:

 

Flush with mineral spirits followed by warm clean water.

WARNING! TO PREVENT FIRE:

 

When using mineral spirits, ground gun by holding it against a 

metal container while flushing.

Water-based (Latex) Paint:

 

Flush with warm clean water.

3. Submerge Suction Tube in 

water or flushing solvent.

7. Sprayer will start pumping and water 

or flushing solvent as well as air 

bubbles will be purged from system. 

Let fluids discharge from Priming Tube 

into waste bucket for 30 to 60 seconds 

then switch Power to Off.

 

11 

 

 

 

 

11 

 

 

 

10. Paint should work itself from 

Suction Tube to Sprayer to Priming 

Tube until paint discharges from 

Return Tube. Point gun into waste 

bucket and pull trigger.

13. Remove the Priming Tube from the 

waste bucket and clip to Suction Tube 

and submerge in paint pail.

14. If the motor stops, the pump and 

tubes are primed. If it does not stop, 

repeat priming steps.

15. Start Painting.

2. Place Priming Tube in waste bucket.

6. Plug in Sprayer and turn on power.

 

11 

 

 

 

 

11 

 

 

 

9. Switch Power to On.

12. Stop spraying and activate trigger lock.

 

11 

 

 

 

1. Separate smaller Priming Tube 

from Suction Tube.

5. Adjust Pressure Control Knob to 

Prime/Clean setting.

 

11 

 

 

 

8. Remove Suction Tube from water 

or flushing solvent and submerge 

in paint pail.

11. Turn Spray/Prime Switch to Spray 

mode and continue to spray into 

waste bucket.

4. Turn Prime/Spray switch to 

Prime mode.

 

11 

 

 

 

Returns not accepted & warranty void if sprayer is 

not properly cleaned immediately after every use.

Returns not accepted & warranty void if sprayer is 

not properly cleaned immediately after every use.

Summary of Contents for Welterweight APS
















Reviews: