background image

02

Specifications & Dimensions

DISCHARGE: 

   

SPHERICAL SLD HNDLG: 
LIQUID TEMPERATURE:

  

VOLUTE:

  

MOTOR HOUSING:

    

SEAL PLATE:

    

IMPELLER:

 

 

SHAFT: 

 

SQUARE RINGS:

 

PAINT:

  

SEAL:   

DIAPHRAGM:

   

HARDWARE:

   

CORD ENTRY: 

 

UPPER BEARING:

 

LOWER BEARING:

 

MOTOR:

 

MOISTURE SENSOR:

 

4", 125lb, flange horizontal.
3"
104° F (40° C) max.
Cast iron ASTM A-48 class 30.
Cast iron ASTM A-48 class 30.
Cast iron ASTM A-48 class 30.
2 vane, open, with vanes on back side. Cast iron ASTM A-48 class 30.
416 series stainless steel.
Buna-N.
Air dry enamel, water based.
Double mechanical, oil filled chamber. Silicon carbide outboard, carbon 

ceramic inboard seal, 

Buna-N elastomer and

 stainless steel hardware.

Buna-N.
300 series stainless steel.
40 ft of neoprene cord SJO 14/3, sealed against moisture.
Ball, single row, oil lubricated, for radial load.
Ball, single row, oil lubricated, for radial and thrust load.

Single  phase:

  NEMA  L,  permanent  split  capacitor,  oil  filled,  with  overload 

protection in motor.

Three phase:

 NEMA B, oil filled. Requires overload protection to be included in 

control panel. Class F insulation.
Normally open (N/O) included, requires relay in control panel.

TEMPERATURE SENSOR

Normally closed (N/C) included, requires relay in control panel.

OPTIONAL EQUIPMENT:

 

Additional cord, tungsten carbide seal, slide rail coupling (SRC-4).

MODEL

HP VOLTS PHASE

RPM

(Nominal)

MAX

AMPS

LOCKED

ROTOR AMPS

NEMA

CODE

CORD

SIZE

CORD

TYPE

CORD

O. D.

WEIGHT

(pounds)

4BSE452DS

4.5

230

1

1750

26

59

A

10/4

SO

0.78"

287

4BSE453DS

4.5

230

3

1750

17.6

56

E

10/4

SO

0.78"

280

4BSE454DS

4.5

460

3

1750

8.8

28

E

10/4

SO

0.78"

280

4BSE752DS

7.5

230

1

1750

39

96

A

10/4

SO

0.78"

315

4BSE753DS

7.5

230

3

1750

23.6

80

D

10/4

SO

0.78"

309

4BSE754DS

7.5

460

3

1750

11.8

40

D

10/4

SO

0.78"

309

4BSE1133DS 11.3

230

3

1750

28.4

126

D

10/4

SO

0.78"

340

4BSE1134DS 11.3

460

3

1750

14.2

63

D

10/4

SO

0.78"

340

4BSE1503DS 15

230

3

1750

40

160

D

10/4

SO

0.78"

399

4BSE1504DS 15

460

3

1750

20

80

D

10/4

SO

0.78"

399

The moisture cord and/or temperature cord is size 18/5, type SO, Ø0.485", for all models.

barmesapumps.com

13.66"

13.66"

20.5"

20.5"

16.5"

16.5"

6.5"

6.5"

35"

35"

5.5"

5.5"

Summary of Contents for 4BSE-DS Series















Reviews: