background image

#0-313A-SBA  (6/01) 
Page 8 of 14 pages 
BARRETT CENTRIFUGALS INC. 
1-800-228-6442 

c.  The cover filter is the largest circular filter.  It has a steel ring located at both the 

inside and outside diameters.  This filter is also held in place with tabs to prevent it 
from falling off during routine use. 

 

2.  All filter elements should be cleaned periodically.  This can be accomplished by 

dipping the filter elements into a water-based detergent bath.  This will clean the 
filter element adequately for immediate installation and use. 

 

1.  Care should be taken when handling the filters so as not to tear or puncture them. 
 
2.  Fine sludge particles may tend to accumulate within the pan cover’s wire mesh element.  

This should be checked daily and cleaned if necessary to insure efficient extraction of fluid 
from the sludge. 

 
 
CARE OF PAN 

From time to time inspect the pan and pan cover  for accumulation of sludge between the ribs of 
the  pan  or  cover. 

If  neglected,  this  will  affect  the  extraction efficiency by blocking the 

escape path for the spun off liquid

.  Clean out any accumulated sludge as required. 

 
 

LOADING AND OPERATING

 

When operating this machine, use care to load the pan evenly to insure a good running 
balance.  Make sure that all guards and covers are in place.

 

 
1.  Before operating the machine be sure that provisions have been made to capture the 

extracted liquid from the outlet at the rear of the machine. 

 
2.  Adjust the cycle timer(s) 1TRE, located within the control panel.  Barrett recommends an 

initial setting of 30 minutes with water-based sludge and 45 minutes with oil-based sludge. 
The required cycle time will vary with the application and must be determined through 
experimentation. Close and latch the control panel’s door. 

 
3.  Turn on the power at the main disconnect.  The green 

OPEN

 light will illuminate within 20 

seconds. 

 

NOTE

:  The machine is wired so that the cooling blower (if so equipped) must be on 

for the machine to operate. 

 

4.  Unlatch and open the machine’s lid.  Remove the pan and pan cover from the machine. 

 

USE CAUTION WHILE OPERATING ANY MACHINERY AND THINK ABOUT THE WORK 

YOU ARE PERFORMING! 

 
5.  Locate a pan already full of sludge or load the wet sludge into a pan.  

  If your machine is a model #401-SE or 1101-SE the pan proper contains no filter 

elements.  

  If your machine is a model #401-SES or 1101-SES the pan should be lined with filter 

elements. The elements attached to the side of the pan need to be adjusted before 

Summary of Contents for 1101
















Reviews: