background image

15

4015 MARINE AUTOMATIC ANTENNA TUNER

to ensure that the purchaser receives full benefit on any warranty given by the 

original equipment manufacturer.

This warranty is restricted to the original purchaser except where the original 

purchaser is a reseller authorised by the Seller who has purchased for the pur-

pose of resale, warranty shall be extended to the reseller’s customer.

Contact Details

Our customer / dealer technical support department can be contacted via land 

mail, email, telephone or via support ticket on the technical support web page. 

https://www.barrettcommunications.com.au/support/

Barrett Communications Pty Ltd Head Office:

PO Box 1214, Bibra Lake WA 6965 AUSTRALIA 

Toll Free Tel: 1800 999 580 (Within Australia)  

Tel: +618 9434 1700  

Fax: +618 9418 6757  

email: 

support@barrettcommunications.com.au

Telephone support from the Australian office is available from 7:30 am to 4:00 

pm local time Monday to Friday.

Barrett Communications – Europe:

Unit 9, Fulcrum 2 Victory Park, Solent Way,  

Whiteley Hampshire PO15 7FN United Kingdom

Tel: +44 (0) 1489 880 332  

Fax: +44 (0) 1489 565 422  

email: 

support@barrettcommunications.co.uk

Telephone support from the UK office is available from 8:30 am to 5:00 pm 

local time Monday to Friday.

Barrett Communications Corporation USA:

90 Office Parkway

Pittsford, N.Y. 14534

United States of America

Tel: +1 585 582 6134

email: 

support@barrettusa.com

Telephone support from the USA support office is available from 8:30 am to 

5:00 pm local time Monday to Friday.

Summary of Contents for 4015

















Reviews: