BARRETT 900 SERIES TRANSCEIVERS
8.0
Internal options
8.1
Internal scrambler option
P/N BCA90031 - available for 940 and 950 transceivers
After removing the jumper JP1 on the RF/Audio PCB, solder the supplied PCB pins into test points
TP9,12,15, and TP24 on the RF/Audio PCB. The optional scrambler PCB is then fitted, the connector on the
scrambler PCB mating with the accessory connector P4 and the PCB pins fitted above mating with the
marked holes. Once in place make sure the scrambler PCB is level and solder the PCB pins to the scrambler
PCB. Note:- the PCB pins from TP9, 12, 15, and TP24 are only used to mechanically secure the scrambler
PCB and make no electrical connection.
The scrambler option is enabled in the setup menu within the transceiver or during programming. Once
enabled the scrambler can be turned off and on by holding down the key labelled "SCRAM". The scrambler
has five Dip switches marked A0, A1, A2, A3 and A4. These allow the scrambling code to be changed as
detailed in the table below. Ensure all transceivers in a net have the same code set to enable reception of
scrambled transmissions.
Note:- a zero means leave the solder link unsoldered, a one means solder the solder link.
Code Number
Address
Code Number
Address
A - A
A - A
4
0
4
0
0
00000
16
10000
1
00001
17
10001
2
00010
18
10010
3
00011
19
10011
4
00100
20
10100
5
00101
21
10101
6
00110
22
10110
7
00111
23
10111
8
01000
24
11000
9
01001
25
11001
10
01010
26
11010
11
01011
27
11011
12
01100
28
11100
13
01101
29
11101
14
01110
30
11110
15
01111
31
11111
PAGE 46
Summary of Contents for 900 Series
