SOUND OPTION
When the safe is open and bolt is retracted,
Sound Off
Press “ CLEAR CLEAR 0530 LOCK”, the display shows
“dONE”, now the Sound is off
Sound On
Press “ CLEAR CLEAR 0531 LOCK”, the display shows
“dONE”, now the Sound is on
LOCK OUT MODE
If the wrong pin code is entered 4 times safe will enter lock out
mode.
User will need to wait 15 min to use safe again; or user can
open safe with override key.
LOW BATTERY WARNING
With safe locked you can push on keypad and press “LOCK”
key; it will show BA-LO.
Means safe battery is low and should be changed as soon as
possible.
CARE AND MAINTENANCE
- To maximize the security and performance of the safe, keep
Fingerprint Scanner clean; use a dry cloth to remove any
smudges or prints off the Fingerprint Scanner after each use
- Test registered fingerprints and PIN code every 6 months
- Keep liquids away from the control panel. Spills on the control
panel will cause damage and possibly electric shock
- Secure safe in a proper area to prevent from falling and
causing damage or injury
- DO NOT disassemble the product. For all repairs, contact
BARSKA Customer Service
- DO NOT use chemicals or cleaning agents to clean the safe
MOUNTING INSTRUCTIONS
The safe may be mounted to a wall or floor. Be aware of the
load bearing. Failure to do so can result in personal injury
and/or damage to property. Use appropriate tools when
performing work and always use eye protection
Wall Mounting
Do not mount the safe without anchoring to the wall
- Find the studs in the wall, at your desired location. Most studs
are 16 inches or 24 inches apart
- Check the wall for concealed wires or pipes
- Measure the location of the pre-set drill holes; mark their exact
position onto the wall ensuring that the studs or anything else
behind will not interfere
- Drill the appropriate size holes for the anchors you are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the safe and
securing to anchors; ensure the safe is mounted securely
Floor Mounting
- Use proper drill tools depending on the type of floor you are
mounting the safe (wood, tile, or concrete)
- Measure the location of the pre-set drill holes; mark their exact
position onto the floor
- Drill the appropriate size holes for the anchors you are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the safe and
securing to anchors; ensure the safe is mounted securely
Safe
BC323
BARSKA warrants this new safe to be free of original defects
in material and/or workmanship under normal use for a
period of twelve (12) months from the date product is
received by purchaser. This warranty does not include
damage caused by improper installation or maintenance.
Damage from misuse, abuse, accident (such as dropping),
normal wear and tear, fire, flood, or acts of nature. Damage
from service or repairs other than those performed by
BARSKA. Labor, cost and shipping charges for the removal
and replacement of defective parts beyond the initial
twelve-month warranty period. All transportation and shipping
charges. Removing or altering the seal under any
circumstances will automatically void the warranty.
This warranty is limited to original purchaser and is not
transferable. This warranty applies only to products
purchased in the United States.
Please email info@barska.com or call 1.888.666.6769 for
Return Merchandise Number (RMA#) before any returns. The
RMA number must appear on the outside of the shipping
package. Product must be packed carefully and sturdily in its
original packaging to prevent damage in transit and returned
freight pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA
products for service and/or replacement:
1. Please write your complete details (Name, Address,
Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $40.00 to cover inspection,
shipping and handling.
*Please allow 6-8 weeks for delivery.
BARSKA will examine and test returned product and repair or
replace defective part(s) or units with new part(s) or a new
unit if necessary within the warranty period. Purchaser is
required to remit $40.00 to BARSKA for return shipping and
handling at time product is returned. If repair is required after
warranty period expiration, purchaser will be
charged for replacement parts and return shipping.
BARSKA® Optics shall not be liable for any consequential,
incidental and/or contingent damages whatsoever. We will
not pay shipping, insurance or transportation charges from
you to us, or any import fees, duties and or taxes. This
warranty supersedes all previous BARSKA® Optics
warranties.
1 YEAR LIMITED WARRANTY
