Инструкция по эксплуатации
Instructions for use
IU 14-223
редакция
4
от
30.05.2017
страница
7
из
18
Настоящий документ является собственностью BARTEC FEAM. Охраняется авторским правом. Частичное или полное воспроизведение разрешено только с разрешения BARTEC FEAM.
The present document is property of BARTEC FEAM. Its copyright in any format, whole or partial, must be before authorized by BARTEC FEAM.
IU 14-223_r4_rus
Должно обеспечиваться минимальное расстояние 50 мм во всех направлениях
между соединительными элементами электрических цепей Ex-i и между цепями
НЕ Ex-i или стенками корпуса (см. РИС. 1).
There must be a minimum distance of 50 mm, measured in every direction, between
the connection components of Ex-i circuits and those of NOT Ex-i circuits, or between
the walls of enclosure (see FIG.1).
-
Блок управления сигнализацией и искробезопасные устройства.
Данное устройство служит для размещения электрического и электронного
оборудования, предназначенного для систем управления питания.
Ввод в эксплуатацию электрического и электронного оборудования должен
производиться исключительно в соответствии с указаниями, содержащимися в
технических паспортах или каталоге поставщика, с соблюдением применимых
стандартов, относящихся к изготовлению электрических щитов низкого
напряжения EN 60439, и общепринятых норм; оборудование должно
находиться на расстоянии не менее 15 мм от внутренних стенок корпусов и не
должно образовывать узких пустых каналов во избежание явлений
предварительного напряжения в случае внутреннего взрыва. Дополнительное
оборудование, установленное на крышке (кнопки, рычаги управления,
сигнальные индикаторы...) установлены в количестве и способом,
предусмотренными в документации, прилагаемой к типовому сертификату
оценки СЕ. Для обеспечения в любой момент полного соблюдения класса
температуры корпуса выделение тепла устройствами, содержащимися внутри
корпусов, должны быть таким, чтобы соблюдались ограничения, указанные в
сертификате.
Клеммы оборудования и составные клеммы должны использоваться для ввода
и подключения проводников допустимого типа и сечения, при этом значения
напряжения и тока не должны превышать параметры, указанные
производителем.
При использовании клемм, предназначенных для искробезопасных
электрических цепей, корпуса должны идентифицироваться
предупредительными табличками с указанием на присутствие внутри
искробезопасных электрических цепей. Внутренние проводные соединения
выполняются с обеспечением минимального расстояния 8 мм между частями
- Control signalling and intrinsically safe component unit.
This apparatus is for the housing of electric and electronic equipment intended for
control and visualisation systems.
The electrical and electronic equipment must be installed according to the instructions
on the supplier’s instruction sheet or catalogue, in accordance with the requirements
established from the certificate standards to apply for the realisation of the electrical
panel with low voltage IEC 61439 and from the art status; the equipment
’s themselves
must maintain the distances of the least 15 mm from the internal walls of the
enclosures and must not create limited tubes of space to avoid eventual phenomenon
of pre stress in case of internal explosion. The accessories mounted on the cover
(push-
buttons, handles, pilot lamps …) are installed in the quantities and conditions
provided from the documents enclosed to the EC-type examination certificate. To
assure in every moment the complete respect of the temperature class assigned to
the enclosure, the thermal dissipation of the devices contained inside of the enclosures
must respect the limits indicated in the certificate.
The terminals of the equipment and the modular ones must be used with the insert
and the connection of the wires of type and section allowed, for voltage and current
values not higher than ones indicated from the constructor.
Where terminals suitable for intrinsically-safe circuits are used, the enclosure must be
identified by means warning labels indicating the presence of intrinsically-safe circuits
inside; internal wiring must be carried out in such a way to ensure a minimum distance
of 8 mm between live portions of NOT Ex-i circuit conductors (degree of insulation
1500V) and Ex-i circuit conductors (degree of insulation
500 V).