background image

Operation 

Ex p Control Unit 

SIEMENS Set 

 

Page 46 of 80 

01-37A2-7D0004_SIEMENS_Manual_Exp-Control-Unit_20220216_0_en.docx 

Rev. 0  

Disclaimer: We reserve the right to make technical changes. Changes, errors and printing errors do not justify claims for damages. 

7

 

Operation 

 

The operation of the Ex p control unit by the end user is described in the 
following chapters. Configuration and setting descriptions are provided in 
separate operating instructions. 

The complete solution starts automatically after connection of the purge gas 
supply and supply voltage. System states can be requested via the WEB 
interface. 

 

 

WEB interface 

 

The Ex p control unit is delivered with a fixed IP address as standard. 

Standard IP address (delivery status): 192.168.11.101 

The following options are available for establishing a connection between laptop 
and PC. 

Laptop (192.168.11.99 // 255.255.0.0) 

Direct 

Indirect  

USB / LAN interface converter 

Ex p control unit (192.168.11.101) 

 

 

Setting the LAN connection 

 

The settings on the PC (or convertor/managed switch) LAN interface must be 
parameterized such that it can communicate with the Ex p control unit. 

 

Settings: 

LAN interface configuration: 

 

Extended / speed: 100 Mbps full duplex 

 

Properties of the internet protocol Version 4 (TCP/IPv4): 

 

Activation of fixed IP address 

 

IP address: 192.168.11.99 

 

Subnet mask: 255.255.0.0 

 
 

 

Summary of Contents for Ex p Control Unit APEX



















































































Reviews: