B1
-A
2Z
0-
7D
00
01
/
Re
vis
ion
A
/
29
Jan
uar
y 2
014
-
Aut
om
ati
on
Tec
hn
olo
gy
-
35
95
18
Operating Instructions
(Translation)
RFID Snap-on Module
for Mobile Computer MC 959x Series
BARTEC GmbH Max-Eyth-Straße 16
97980 Bad Mergentheim
Germany
Tel.: +49 7931 597-0
Fax: +49 7931 597-119
info@bartec.de
www.bartec.de
Reservation Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.
1/5
1. Description
The "RFID Snap-on Module" reads and writes RFID tags. It was designed for
the Mobile Computer MC 959x series.
A C# package containing all the
components and resources that are
required for software integration is
available to software developers. A
demonstration program (programmed in
Visual Studio 2008) in Open Source
makes it possible to conduct a simple
demonstration and test for correct
functioning.
Type
RFID frequency range
LF
125 kHz / 134 kHz
HF
13.56 MHz
UHF (EU)
865.6 to 867.5 MHz
UHF (US)
902 to 928 MHz
The RFID reader is supplied voltage through the external interface at the back
of the MC 959x. Data communication is enabled by the USB interface.
The reader is available in a standard version (non-Ex) and in an explosion-
proof version.
Device
Configuration
Motorola Solutions
Device
Configuration
BARTEC
MC 9590 Standard version
MC 9590
ex
-NI Ex-proof
MC 9596 Standard version GSM
MC 9596
ex
-NI Ex-proof GSM
MC 9598 Standard version CDMA
MC 9598
ex
-NI Ex-proof CDMA
Use in Accordance with the Intended Purpose
The RFID Snap-on Modules are electrical apparatus designed as accessories
for the hand-held mobile computers in the MC 959x and MC 959x
ex
-NI series.
The modules can be used only in combination with the Mobile Computer.
They capture, process and transmit data inside and outside hazardous areas.
Available for:
Standard version – not explosion-proof
ATEX/IECEx Zone 2 and Zone 22
UL Class I, II Division 2, Class III
It is used exclusively in combination with operating equipment items which
conform to the requirements of Overvoltage Category I.
Other applicable documents
-
Technical data sheet for the explosion-proof and standard
versions of the RFID snap-on module
-
Description of BARTEC’s Open Source software packet
for RFID snap-on module implementation in one customer
application.
-
Technical data sheet for the explosion-proof version of the
MC 959x
ex
-NI Mobile Computer series
-
User manual for the MC 959x Mobile Computer series
The retention of these documents is mandatory!
2. Safety Instructions
The "RFID Snap-on Module" may be operated only if it is clean and free of
any damage and only within the specified temperature class and the
temperature range indicated for it. It is essential to comply with the
permissible operating data for the device being used. Utilisation in areas other
than those specified and the modification of the product by anyone other than
the manufacturer is not permitted and will exempt BARTEC from liability for
defects and any further liability. The generally applicable statutory rules and
other binding directives relating to workplace safety, accident prevention and
environmental protection must be observed.
Danger, Warning and Information Symbols
Safety instructions and warnings are specially highlighted in this manual and
marked by symbols.
DANGER
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING
WARNING indicates a hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION
CAUTION indicates a hazardous situation
which, if not avoided, could result in minor or
moderate injury.
ATTENTION
ATTENTION identifies a potentially
damaging situation which, if not avoided,
could damage the equipment or something in
its environment.
Important instructions and information on effective, economical and
environmentally compatible handling.
3. Technical Data
Explosion Protection
ATEX Zone 2 and Zone 22 and IECEx Zone 2 and 22
Types
B7-A2Z0-0020
B7-A2Z0-0022
B7-A2Z0-0021
B7-A2Z0-0023
ATEX approval
EPS 13 ATEX 1588 X
ATEX marking
II 3G Ex ic IIC T6 Gc
II 3D Ex ic IIIC T90°C Dc
IECEx approval
IECEx EPS 13.0028 X
IECEx marking
Ex ic IIC T6 Gc
Ex ic IIIC T90°C Dc
Directives
94/9/EC
Standards
EN 60079-0
EN 60079-11
UL Class I Division 2
Types
B7-A2Z0-0020
B7-A2Z0-0022
B7-A2Z0-0021
B7-A2Z0-0023
UL approval
E321557
UL marking
Class I Division 2 groups A, B, C and D
Class II Division 2 groups F and G
Class III
Temperature class
T5
Special Conditions for ATEX and UL
It is not permissible to attach or remove the RFID Snap-on Module inside
the hazardous area.
Conditions particulières applicables aux équipements ATEX et UL
Il est strictement interdit de clipser ou déclipser le module RFID en zone
dangereuse.
