background image

OPERATION

5

6

OPERATING INSTRUCTIONS

LIGHTING

1. make sure there is only a small amount of ash in the bottom of the bowl.

2. place a layer of dry kindling or a natural firestarter onto the center of the grate.

3. 

place above that a layer of dry seasoned hardwood that is cut to lengths no more than 

3/4 the diameter of the bowl.

4. use a match to light kindling or firestarter.

5. using a hook and heat resistant gloves,replace spark guard once the kindling or firestarter 

is lit.

TENDING THE FIRE

You may need to shift and/or add logs for an ideal experience.  CAUTION: DO NOT place 

a hot spark guard or hot fire bowl tools onto combustible surfaces such as grass, wooden 

deck or furniture.

1. Using a hook and heat resistant gloves, carefully remove spark guard.

2. While using a long handled fire pit tool, shift coals and logs to allow additional airflow.

3. DO

 NOT add gasoline, kerosene, diesel fuel, lighter fluid or alcohol to relight or enhance 

an existing fire.

4. W

ait until glowing coals have developed before adding any additional wood. If additional 

wood is required, place wood on top coals. Be careful not to shift ashes.

5. Using a hook and heat resistant gloves, replace spark guard.

EXTINGUISHING 

1. Allow fire to burn itself out.

2. DO NOT use water to extinguish as this is dangerous and can cause damage to this outdoor 

fire pit.

CLEANING AND CARE

Inspecting This outdoor fire pit should be inspected on a regular basis to ensure product 

safety and longer product life. CAUTION: DO NOT attempt to inspect this outdoor fire pit 

until the fire is completely out.

1. Check handles to make sure they are secure.

2. Check components for any signs of damage or rust.

3. I

f damage to any components is detected, DO NOT operate until repairs are executed.

CLEANING 

This outdoor fire pit should be inspected on a regular basis to ensure product safety and 

longer product life.

Note: After repeated use, a slight discoloration of the finish may occur.

STORAGE

CAUTION: DO NOT move or store this outdoor fire pit until the fire is completely out.

1. Once the fire is out, coals are cold and outdoor fire pit is cool to the touch, remove ashes 

and properly dispose. 

2. Store assembled in a location away from children and pets. 

Summary of Contents for 96811









Reviews: