background image

 

 

 

- 13 - 

Technical data 

 
 

Description

 

Pump sauce dispenser

 

Model:

 

1 pump 

2 pumps 

3 pumps 

4 pumps 

Item no.:

 

100.321 

100.322 

100.323 

100.324 

Body:

 

Chrome nickel steel 18/10

 

Pump: 

Polycarbonate, inner pot polyethylene 

Capacity:

 

3,3 L 

2 x 3,3 L 

3 x 3,3 L 

4 x 3,3 L 

Dimensions:

 

W x D x H (mm):

 

139 x 224 x 456  276 x 224 x 456  394 x 224 x 456  511 x 224 x 456 

Accessories:

 

3 different dosing inserts per pump

 

 

 

Description

 

Pump sauce dispenser with top-cover

 

Model:

 

for 1/6 GN-container, 

150 mm deep

 

for 1/4 GN-container,  

150 mm deep

 

for 1/3 GN-container, 

150 mm deep

 

Item no.:

 

100.330 

100.331 

100.332 

Lid: 

Chrome nickel steel 18/10 

Pump:

 

Polycarbonate

 

Dimensions:

 

W x D x H (mm):

 

165 x 181 x 232  

168 x 267 x 232 

181 x 334 x 232 

Accessories:

 

3 different dosing inserts

 

We reserve the right to make technical changes! 

 
 

Intended use 

 

The condiment pumps are intended only for ketchup, mayonnaise, mustard and cold 
sauces
.  

  CAUTION! 

Any use going beyond the intended purpose and/or any different use of the 
device is forbidden and is not considered as conventional. 

Any claims against the manufacturer or his authorized representative as a 
consequence of experiencing damages resulting from unconventional use are 
impossible. 

The operator is liable for all damages resulting from inappropriate use. 

 

 

GB/UK 

Summary of Contents for 100.321











Reviews: