background image

 

 

 

 

- 26 - 

 

Problem 

Cause 

Solution 

Device functions 
loudly. 

 

  Freezer is on an uneven 

surface. 

  Freezer is touching wall or 

other objects. 

 

 

 

Place freezer on an even 
surface. 

 

Leave proper distance 
between freezer and 
other objects. 

Compressor fails 
to come on 
automatically. 

 

  Drinks freezer is overfull. 

 

  Doors opened for too long. 

 

 Remove 

unnecessary 

objects. 

 

Keep doors open for as 
short a time as possible. 

 

The above described problem cases are given for orientation and as examples. 
Should these or similar problems occur, please turn off the machine immediately 
and don´t use it anymore. In order to check and repair your machine, please contact 
a qualified expert or the manufacturer immediately. 

 
 

The following are not malfunctions: 

 

1.  Sound of flowing eater. This sound occurs during normal use of the device. This is 

the cooling device inside the refrigerator. 

2.  The freezer needs some time in order to reach the desired temperature. An increase 

in temperature inside the unit as well as outside will extend the time necessary for 
the unit to reach the desired temperature. 

3.  The compressor’s surface may be hot during normal use.  

  WARNING! Danger of burns! 

Do not touch the compressor’s surface with bare hands.  

 
 
 

 
 
 
 
 

www.food-service.com.ua

Summary of Contents for 700.075H















Reviews: