background image

 

 

 

- 30 - 

 

 

During the operation of the device do not put hands or other 
body parts in the pot. 

 

Never 

immerse the device in the pot with the processed food 

products 

deeper than the immersion mark

.  

 

Never remove the device from the pot before its 
complete stop and never earlier than 10 seconds from 
turning the device off. 

 

Never 

remove safeguards and warning labels from the device, 

either partially or fully. 

 

Never 

insert any objects inside ventilation holes of the device 

body. 

 

Never 

place or lay the device 

on objects other than the wor-

king table, 

which must be fitted for food products and its height 

from the floor must be within the range from 900 to 1100 mm. 

 

Never use 

flammable, corrosive or toxic cleaning agents 

and 

excessively alkaline

 

ones, like e.g. sodium hydroxide 

or ammonia. 

 

Never allow unauthorized persons 

or persons not wearing 

recommended protective clothing 

to use the device

 

It is forbidden 

to use the whip in the devices without 

adjustable speed. 

 

Never use the device in the direct vicinity of open flame or 
glowing materials, unless appropriate safeguards are in place. 

 

Never 

use the device when all 

conditions

 

ensuring 

elimination of the residual risk 

are not fulfilled.

 

Summary of Contents for MX 235 Plus SB170


























Reviews: