background image

 

 

 

- 31 - 

 

 

WARNING

 

The residual risk results from removing 

permanent covers and tampering with damaged / used parts! 

 

 

The operator absolutely must not attempt to open or 
remove the permanent covers or protective elements. 

 

During 

completion, maintenance and cleaning 

and 

other 

similar manual activities, 

connected with placing hands or 

other body parts in the hazardous areas of the device, there is 
the residual risk which may result in: 

1. 

hitting the device parts; 

2. 

abrasion and/or scratches due to contact with rough 

device parts; 

3. 

injuries inflicted by sharp parts; 

4. 

cutting wounds due to contact with sharp parts, 

5.

 entangling in moving parts (whip)  

 

 

Due to the need of placing hands in the vicinity of the knife during 

cleaning or removing residues, 

there is a residual risk 

consisting in the 

possibility of injuries with sharp objects.

 

 

Therefore, the persons operating and performing maintenance 
of the device 

must be trained in performing activities with 

open covers 

and must be informed of resulting hazards, as 

well as authorized by the responsible person.  
They must also use appropriate personal protective equipment 
or wear 

cut resistant gloves

 

Summary of Contents for MX 235 Plus SB170


























Reviews: