background image

 

 

ACCESSORIES AND SPARE PARTS 

 

 

Description 

Part Number 

1. 

Probes and Hoses  

 

 

 

 

Gooseneck Probe with Quick Connect and Filter (14 inch long) ...................................  

GP 

514 

 

Surface Probe (with Quick Connect and Cone)..............................................................  

SP 

636 

 

Ceiling/Bar Hole Probe & Rubber Tip (34 inch long, clear) ..........................................  

BP 

034 

 

Clear Bar Hole Probe (34 inch long, clear, side holes) ..................................................  

BP 

134 

 

Fiberglass Bar Hole Probe (36 inch long, no side holes) ...............................................  

BP 

136 

 

Two-Piece Bar Hole Probe (24 inch long when put together)…………………………. 

BP 

224 

 

Fiberglass Bar Hole Probe (36 inch long, side holes) ....................................................  

BP 

236 

 

Metal Bar Hole Probe (36 inch long, side holes) ...........................................................  

BP 

536 

 

Standard Flue Gas Probe & Filter (10 inch long) ...........................................................  

FP 

110 

 

Heavy Duty Flue Gas Probe & Filter .............................................................................  

FP 

112 

 

Straight Hose with Quick Connect Fitting (42 in. long) .................................................  

QH 

042 

 

Straight Hose with Quick Connect Fitting (5 ft. long) ...................................................  

SQ 

060 

 

 

 

 

 

2. 

Filters 

 

 

 

 

Dust & Water-block Filter (5/pkg) .................................................................................  

WF 

505 

 

Dust and Water-block Filter for Models EGA-611/612 (5/pkg) ....................................  

WF 

705 

 

Water-stopper (with push-button release) ......................................................................  

WS 

001 

 

Dust Stopper (with replaceable filter) ............................................................................  

DS 

001 

 

Replacement Dust Filters (5/pkg) ..................................................................................  

DF 

105 

 

Flue Gas Filter (5/pkg) ...................................................................................................  

FF 

005 

 

Extended Duty Flue Gas Filter (5/pkg) ..........................................................................  

FF 

105 

 

Heavy Hydrocarbon Filter (5/pkg) .................................................................................  

HF 

005 

 

Inlet Filter & Quick Connect Air Intake (5/pkg) ............................................................  

IF 

705 

 

 

 

 

 

3. 

Sensors 

 

 

 

 

Methane Sensor (in flame arrestor) ................................................................................  

MS 

511 

 

CO Sensor ......................................................................................................................  

CO 

302 

 

Oxygen Sensor (J Series)  ..............................................................................................  

OS 

501 

 

Oxygen Sensor (K Series) ……………………………………………………………... 

OS 

502 

 

Combination

 

CO/H2S Sensor…………………………….…………………………….               

        

CS            -     601 

4. 

Replacement Parts, and Manual 

 

 

 

 

Pump Motor ...................................................................................................................  

PM 

501 

 

Pump Head, Diaphragm/Plunger Assembly (5 sets/pkg) ...............................................  

PD 

505 

 

Intake Manifold with Pump ...........................................................................................  

RM 

501 

 

Battery Compartment Cap .............................................................................................  

BC 

501 

 

Operating Manual ..........................................................................................................  

OM 

0215 

 

 

 

 

 

5. 

Instrument Case 

 

 

 

 

Instrument Case w/Ethafoam Insert ...............................................................................  

IC 

501 

 

 

 

 

 

6. 

Accessories for Calibration & Maintenance 

 

 

 

 

Manual Calibration Apparatus (with MC-620 & FR-401) .............................................  

PCA 

302 

 

Methane & CO Calibration Gas (2.5%  methane & 100 ppm CO, 620 liters)................  

MC 

620 

 

On-demand Regulator for MC-620 ................................................................................  

FR 

401 

 

Rechargeable C-Sized Batteries (NiMH, 4/pkg) ............................................................  

NM 

524 

 

Rapid Charger for 2 to 4 C-Sized Batteries ....................................................................  

RC 

502 

Prices and Terms 

 

 

 

 

Prices and specifications are subject to change without notice.  Prices are U.S. dollars.  Orders are subject to acceptance 

and are FOB Norwood, Massachusetts.  Payment terms are Net 30 days.  Minimum order is $50.

 

 

 
 
 

  

 

Summary of Contents for GAS-EXPLORER OM-0517





























Reviews: