•
Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or subjected to mechanical
stress. Avoid excessive thermal stress on the mains cable from extreme heat or cold. Do not attempt to
modify the mains cable, as this may cause permanent damage. Damaged mains cables can cause a fatal
electric shock.
•
Do not touch the mains cable if there are any signs of damage. Power down the respective mains socket (e.g.
via the respective circuit breaker), and then carefully pull the mains plug from the mains socket. Never use
the product if the mains cable is damaged.
•
Damaged mains cables must be replaced by the manufacturer, an authorized repair centre or a qualified
electrician.
•
Never insert or unplug the mains plug when your hands are wet.
c) Product
•
This device was constructed according to protection class II. The product must only be powered by a standard
mains socket connected to the public grid.
•
Before connecting the product to the mains, check that your household mains voltage meets the specifications
on the product name place.
•
Never use the product immediately after it has been brought from a cold room into a warm one. The
condensation generated may destroy the product. Allow the product to reach room temperature before
connecting it and putting it to use. This may take several hours.
•
Never touch the product when your hands are wet or damp, as this may cause an electric shock.
•
Do not immerse the product in water.
•
Never use the product without the soldering tips.
d) Soldering
•
Do not use the soldering gun to solder live components.
•
Always ensure that there is sufficient ventilation. Soldering and flux vapours can be harmful to your health.
•
Always wear suitable protective clothing and safety goggles.
•
Only solder on non-flammable surfaces. Ensure that there are no materials that may be damaged by the heat
generated from the soldering gun.
•
Do not solder near to flammable materials or in rooms containing explosive substances.
Operation
a) Attaching/replacing the soldering tips
•
Allow the soldering gun and tips to cool down completely.
•
Use a screwdriver to loosen the screws on the soldering tip socket, and then remove the soldering tip.
•
Insert a new soldering tip and screw it into place.
b) Soldering
Never touch a hot soldering tip.
Burn hazard!
Observe the working intervals (
max. 12 secs on
, and then
min. 48 secs off).
•
Ensure that the soldering contacts on the workpiece are clean.
•
Connect the soldering gun to the mains.
• Press the trigger to heat the soldering gun. The solder joint indicator turns on to indicate that the soldering gun is heating.
-
Wait 12 secs for the soldering gun to heat up.
•
Apply solder to the heated soldering tip.
•
Heat the soldering point and apply solder.
•
Allow the soldering point to cool down.
•
Clean the hot soldering tip with a wet sponge.
-
Do not file the soldering tip, as this may cause permanent damage.
•
When you have finished soldering, release the trigger on the soldering gun.
•
After use, remove the mains plug from the mains socket and allow the soldering gun to cool down.
Care and cleaning
•
Always disconnect the product from the power supply before cleaning it.
•
Allow the product to cool down to room temperature before cleaning or servicing.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may damage the casing or cause
the product to malfunction.
•
Use a dry, lint-free cloth to clean the product.
a)
Replacing the solder joint indicator
• Remove the defective light from the socket.
•
Replace it with a new light of the same type.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste. Always dispose of the product
according to the relevant statutory regulations.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
Input voltage
....................................................
230 V/AC, 50 Hz
Power consumption
.........................................
Max. 100 W
Protection class ...............................................
II
Light .................................................................
2.2 V / 0.25 A, E10 conical lens
Cable length
....................................................
1.4 m
Operating time
.................................................
Max. 12 secs ON, then min. 48 secs OFF
Operating/storage conditions
...........................
0 to +40 °C, 20–90 % relative humidity (non-condensing)
Dimensions (H x W x D)
..................................
172 x 51 x 149 mm (without tip)
Weight .............................................................
635 g (without tip)
Operating instructions
Soldering gun, 100 W
Item no. 1553618
Intended use
This product is designed for soldering joints. It can be used in a wide range of scenarios, such as workshops, the service
industry, and for DIY purposes.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g. in bathrooms) must be avoided
under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. Using the product for purposes other than
those described above may damage the product. In addition, improper use can cause hazards such as a short circuit, fire or
electric shock. Read the instructions carefully and store them in a safe place. Make this product available to third parties only
together with its operating instructions.
This product complies with statutory national and European regulations. All company and product names are trademarks of
their respective owners. All rights reserved.
Delivery content
• Soldering gun
•
3x soldering tips
•
Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code on this page. Follow the
instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle indicates that there is a risk to your health, e.g. due to an electric shock.
This symbol is used to highlight important information in these operating instructions. Always read this information
carefully.
Important safety information
•
This appliance may be used by children over 8 years
of age and people with reduced physical, sensory or
mental capabilities if they have been given supervision
or instruction concerning the safe use of the appliance
and understand the potential hazards.
•
Children should always be supervised by an adult to
ensure that they do not play with the appliance.
•
Children must not clean or service the product without
appropriate supervision.
General safety instructions
Read the operating instructions carefully and especially observe the safety information. If you do not
follow the safety instructions and information on proper handling in this manual, we will assume no
liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
•
This product is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly, as it may become dangerous playing material for
children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, stop using it and prevent unauthorized use. Safe
operation can no longer be guaranteed if the product:
- is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stress.
•
Always handle the product carefully. Jolts, impacts or a fall even from a low height may damage the product.
•
Consult a technician if you are not sure how to use or connect the product.
•
Maintenance, modifications and repairs must be done by a technician or an authorized repair centre.
•
If you have questions which remain unanswered by these operating instructions, contact our technical support
service or other technical personnel.
b) Cable
• The mains outlet must be located near to the device and be easily accessible.
•
Never unplug the mains plug by pulling on the cable. Always use the grips on the plug.
•
Unplug the mains plug from the mains socket if you do not plan to use the device for an extended period
of time.
•
For safety reasons, unplug the mains plug from the mains socket during thunderstorms.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*1553618_v1_0917_02_jh_m_4L_(1)
