1-4
BE1-50 General Information
I
K
t
Table 1-1. Current Ratings and Sensing Burdens
Power
Supply
Sensing Range
Designation
Actual
Sensing
Range
Maximum Rating
50 or 60 Hz
For
Phase
For
Neutral
Current
Burden
Per Input
K*
1 Second
Continuous
1
D
0.25 - 0.5A
144
12.0A
0.75A
8.5VA
2
E
0.5 - 1.0A
144
12.0A
1.5A
8.5VA
F, G
3
F
1.0 - 2.0A
625
25.0A
3A
8.5VA
or H
4
G
2.0 - 4.0A
2500
50.0A
6A
8.5VA
5
H
4.0 - 8.0A
10000
100 A
12A
8.5VA
6
J
8.0 - 16.0A
40000
200 A
20A
9.5VA
7
K
16.0 - 32.0A
90000
300 A
20A
14.0VA
O, P,
2
E
0.25 - 2.0A
10000
100 A
5A
0.2VA
R, S
4
G
1.0 - 8.0A
90000
300 A
10A
0.6VA
or T
6
J
4.0 - 32.0A
90000
300 A
20A
4.8VA
* Ratings other than continuous may be calculated using the equation:
where:
K
= the indicated value
t
= the time in seconds
I
=
maximum current
Table 1-2. Power Supply Burden
Type
Nominal Input
Voltage
Input Voltage
Range
Burden at
Nominal
O (Mid Range)
48 Vdc
24 to 150 Vdc
4.0 W
P (Mid Range)
125 Vdc
120 Vac
24 to 150 Vdc
90 to 132 Vac
4.0 W
10.0 VA
R (Low Range)
24 Vdc
12† to 32 Vdc
4.0 W
S (Mid Range)
48 Vdc
125 Vdc
24 to 150 Vdc
24 to 150 Vdc
4.0 W
4.0 W
T (High Range)
250 Vdc
240 Vac
62 to 280 Vdc
90 to 270 Vac
6.0 W
14.0 VA
†
Type R power supply initially requires 14 Vdc to begin operating. Once operating, the voltage
may be reduced to 12 Vdc and operation will continue.
Output Circuits
Output contacts are rated as follows:
Resistive:
120/240 Vac
Make 30 A for 0.2 seconds, carry 7 A continuously, and break 7 A.
250 Vdc
Make 30 A for 0.2 seconds, carry 7 A continuously, and break 0.3 A.
Inductive:
120/240 Vac,
Make 30 A for 0.2 seconds, carry 7 A continuously, and break
125/250 Vdc
0.3 A. (L/R = 0.04).
Summary of Contents for BE1-50
