To reset the alarms using BESTCOMS select
Reporting and Alarms
from the
Screens
pull-down menu.
Then select the
Alarms
tab. Select the
Logic
button in the
BESTlogic
box on the right side of the screen.
Refer to Figure 6-26. The
BESTlogic Function Element
screen for
Alarm Reset Logic
will appear. See
Figure 6-29.
To connect the function's input, select the
Reset
button in the
BESTlogic Function Element
screen. The
BESTlogic Expression Builder
screen will open. Select the expression type to be used. Then, select the
BESTlogic variable, or series of variables to be connected to the input. Select
Save
when finished to
return to the
BESTlogic Function Element
screen. For more details on the
BESTlogic Expression Builder
,
see Section 7,
BESTlogic Programmable Logic
. Select
Done
when the settings have been completely
edited.
Figure 6-29. BESTlogic Function Element Screen, Alarm Reset Logic
BESTlogic Elements Controlled by Programmable Alarms
Major, Minor, and Logic programmable alarm settings drive BESTlogic variables ALMMAJ, ALMMIN, and
ALMLGC. These variables can be used in logic expressions to control logic when the alarm is active. For
example, these variables could be used to actuate an output relay to signal a SCADA RTU that an alarm
condition exists.
HARDWARE AND SOFTWARE VERSION REPORTING
Hardware and software version reporting is used to determine what style chart selections are included in
the relay, the relay serial number and the version of the embedded software (firmware).
Model (style) number serial number information is contained on the label on the front panel. Embedded
software information can be obtained at HMI Screen 4.6, \REPRT\VERSION. The information of Screen
4.6 is also displayed briefly when operating power is applied to the relay.
A software and hardware version report can be obtained through BESTCOMS. Alternately, it can be
obtained using the RG-VER ASCII command.
To obtain the relay's version report through BESTCOMS, select
Download Settings from Device
from the
Communication
pull-down menu. Downloaded settings from the relay will overwrite any settings you have
made in BESTCOMS; the relay will ask you to save your current file before continuing the download.
To view the version of the relay once the download is complete, select
General Operation
from the
Screens
pull-down menu. Then select the
Identification
tab (Figure 6-30). The
General Info
tab (Figure 6-
31) displays all of the style information about the relay.
6-44
BE1-CDS240 Reporting and Alarm Functions
9365200990 Rev F
Summary of Contents for BE1-CDS240
