manualshive.com logo in svg

Basler BE1-CDS240, Instruction Manual

The Basler BE1-CDS240 Instruction Manual is available for free download on our website. This comprehensive manual provides users with detailed instructions and information on operating and troubleshooting the Basler BE1-CDS240 product. Easily access the manual at 88.208.23.73:8080 and optimize your experience with this versatile product.

Share
Download
background image

NOTE 

The CT input circuit settings are used by the auto-tap calculation function to 
calculate the correct tap adjustment factor for the differential functions. When 
entering these settings via the ASCII command interface, the validation routine 
and auto-tap calculation is performed on exit after all parameters have been 
entered.  

When entering these settings using the optional HMI, the validation routine and 
auto-tap calculation is performed on exit of each screen. This may cause an 

OUT 

OF RANGE

 error message from the auto-tap calculation function. The user is 

advised to enter valid CT input circuit settings on Screen 6.3.1.1, 
SETUP\PWR_S\CON\CTP prior to entering the auto-tap calculation settings. If 
the user has previously set the auto-tap calculation settings and needs to change 
the CT input circuit settings, it may be necessary to temporarily change the auto-
tap function setting to 

MANUAL

 on Screens 5.1.1.3, 5.2.1.3, 5.3.1.3, and 5.4.1.3  

\PROT\SG#\87\TAP in order to enter the new CT settings.   

See Section 3, 

Input and Output Functions, Power System Inputs,

 for more 

information on CT input circuit settings.  

The tap factors calculated by the auto-tap calculation feature can be determined in several ways. They 
are displayed on the optional HMI using Screen 5.#.1.2, \PROT\SG#\87\MVA. Alternatively, the current 
check record provided by the differential alarm function includes a listing of the compensation parameters 
in the setting group that was active at the time that the record was triggered. See Section 6, 

Reporting 

and Alarm Functions, Differential Current Monitoring Function, Setting Differential Current Monitoring 
Alarms, 

for more details on this report.  

Operating Settings for Phase Differential 

Operating settings for the 87 function consist of 

Restrained Pickup

, 

Restraint Slope

, 

2

nd

 and 5

th

 Harmonic 

Restraint

, and 

Unrestrained Pickup

 values.  

Operating settings are made using BESTCOMS. Figure 4-12 illustrates the BESTCOMS screen used to 
select operational settings for the 87 function. To open the screen, select 

Percentage Differential

 from the 

Screens

 pull-down menu. Then select the 

87 Phase

 tab. Alternately, settings may be made using S<g>-

87 ASCII command or through the optional HMI Screens 5.#.1.1, \PROT\SG#\87\87. 

The operating settings for Phase Differential are provided in Table 4-7.  

The settings for restrained minimum pickup and unrestrained trip are set in multiples of tap. If the ideal 
taps calculated by Equation 4-1 fell within the acceptable range, the sensitivity settings will be in 

Per Unit

 

on the MVA Base used in the equation. For example, a 100 MVA, 115 KV transformer has a full load (1 
per unit) current of 500 amperes. A pickup setting of 10 times tap for the unrestrained output pickup 
(URO) element is equivalent to 5,000 primary amperes of differential current.   

If the taps had to be adjusted upwards or downwards to fit within the acceptable range, the sensitivity 
settings for these protective elements should be adjusted as well. Equation 4-2 gives the adjustment 
factor. The definitions for the variables in Equation 4-2 are the same as those for Equation 4-1. For 
example, the ideal taps 

(

TAPn

I

)

 were calculated using Equations 4-2 and 4-3 to be 1.6 and 5.0. They had 

to be adjusted upwards so that the actual taps 

(

TAPn

A

)

 are 2.0 and 6.25. Per Equation 4-2, 

X

 is 0.8. It is 

desired that the minimum pickup of the restrained element be 0.35 per unit on the circuit base. The actual 
setting should be 0.35 

 0.8 = 0.28 to achieve the same sensitivity. 

The pickup settings in 

Times Tap

 can be related to primary amps by Equation 4-3. 

Minpu

 is the minimum 

pickup setting in Times Tap. The definitions for the remaining variables in Equation 4-3 are the same as 
those for Equation 4-1. 

 

CTRn

*

KVn

*

3

*

TAPn

COMPn

*

1000

*

MVA

TAPn

TAPn

X

A

A

I

 

 

Equation 4-2. Tab Adjustment Equation 

COMPn

CTRn

*

TAPn

*

Mpu

Ipri

 

 

Equation 4-3. Calculate Primary Amps 

 

9365200990 Rev F 

BE1-CDS240 Protection and Control 

4-15 

Summary of Contents for BE1-CDS240





































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BE1-CDS240

Furman PF-Pro R Owner'S Manual preview
PF-Pro R
Brand: Furman Pages: 8
Ground Zero GZ PROtect Owner'S Manual preview
GZ PROtect
Brand: Ground Zero Pages: 4
Value 19.99.3420 User Manual preview
19.99.3420
Brand: Value Pages: 24
ABB System pro E power Instruction Handbook preview
System pro E power
Brand: ABB Pages: 4
Datavideo PD-6 Quick Start Manual preview
PD-6
Brand: Datavideo Pages: 8
B&K IR80 User Manual preview
IR80
Brand: B&K Pages: 2
Zero88 Chilli Pro 12 Manual preview
Chilli Pro 12
Brand: Zero88 Pages: 60
Tripp Lite 200803016 95-2924 Technical Application Bulletin preview
200803016 95-2924
Brand: Tripp Lite Pages: 8
Portawattz POWER PAC Owners Man preview
POWER PAC
Brand: Portawattz Pages: 32
Ajax TOCCO Toccotron AC Owner'S Manual preview
Toccotron AC
Brand: Ajax TOCCO Pages: 52

Brands by name

Popular brands

Load more brands