background image

page 26

Basta Boatlifts Limited Warranty

Thank you for investing in one of the finest PWC lifts in the world. We pride 

ourselves in knowing our product will safely and reliably be the conduit to your fun 

on the water. Welcome to the Basta Boatlifts family and Boat Happy! 

Basta Inc. dba Basta Boatlifts (“Company”) warrants its Products (purchased 

 

after November 1st, 2021) for non-commercial use for a period of, 
.   16 years against manufacturing defects in steel and aluminum 

    lift frame welds. 
.   3 years against defects in materials and workmanship including

    hydraulic components, charging system, remote controls, dock box, 

 

    bunks, canopies, and accessories.  
.   1 year battery warranty when maintained in accordance with

battery manufacturer’s guidance for batteries supplied 

    by the Company,

to the original Purchaser (“Purchaser”), beginning from date of purchase of the 

Product from Company. If the Product is purchased from an authorized Company 

Reseller, the warranty term begins upon the date the new Product is sold to the end 

Purchaser (“Warranty Start Date”).

Annual inspection of the Product bolts, pins, hydraulics, pump, electronics, and 

 

welds, by a Company employee or Company authorized agent, shall be conducted. 

Failure to undertake such maintenance shall constitute “abuse” under Exclusions 

below.

Company has the right to modify Products at any time without incurring any 

obligation to make the same or similar modifications on Products previously 

manufactured or purchased.

Terms And Conditions:

Purchaser must register Product for a valid Warranty. Warranty registration may be 

found and submitted at: 

https://bastaboatlifts.com/support.

Notice requirements and remedies:

If the Purchaser discovers a defect, the purchaser shall immediately notify the 

Company in writing by submission of a Warranty Claim form. Warranty Claim forms 

may be found and submitted at https://bastaboatlifts.com/support. Upon receipt 

of a complete Warranty Claim form and after confirmation by Company that the 

Product is defective, the Company, or its authorized Company dealer or agent, will, 

at the Company’s sole discretion: 

1- repair the Product or,

2-replace the defective part with a new or  reconditioned part, or 

3-refund the purchase price of the Product. 

Purchaser agrees to pay for door to door freight of warranted Product. Warranty 

replacement shall not extend the original warranty of the defective Products.

Labor for warranty work to be provided by the Company’s Authorized dealer for a 

period of 3 years from Warranty Start Date, provided there is an active Authorized 

Dealer within 50 miles of the location of the Product. Labor will not be provided for 

direct purchases from Company or when an active Authorized Dealer is not located 

within 50 miles of the location of the Product. 

Warranty requests received after expiration of warranty term will not be 

covered under this warranty regardless of when the defect occurred or was 

discovered.

Confirmation of the defect shall require that reasonable proof of the defect be 

provided by Purchaser to Company or Company authorized agent, and may include 

that the Product or part be Returned to Company for inspection at the Purchaser’s 

initial expense. Replacement parts for Products outside the United States will be 

shipped in the next authorized Dealer shipment unless Purchaser agrees to pay for 

door to door freight of warranted Product. Warranty replacement shall not extend 

the original warranty of the defective Products.  

Labor for warranty work to be provided by the Company’s Authorized dealer for 

a period of 3 years from Warranty Start Date, provided there is an active 

Authorized Dealer within 50 miles of the location of the Product. Labor will not be 

provided for direct purchases from Company or when an active Authorized Dealer 

is not located within 50 miles of the location of the Product. 

Warranty requests received after expiration of warranty term will not be covered 

under this warranty regardless of when the defect occurred or was discovered.

Exclusions:

Product changes caused by age or environment (such as marine growth, 

heat, corrosion or electrolysis) shall not constitute a defect. In addition, this 

warranty does not cover or apply to the following: damages caused by or due to 

without limitation: accidents, collision, fire, flood, wind, ice, or any other natural 

disaster or acts of God, abuse, misuse, overloading, improper watercraft loading, 

use when out of level, faulty assembly or installation. Lift components’ fluid levels 

and condition, including battery electrolyte (water and acid), hydraulic fluid and 

strainer cleaning are maintenance items and are not covered by this warranty. 

Sacrificial anodes (zincs), cosmetic concerns and custom coatings are not covered 

by this warranty. 

Warranty is void if the Product has been modified in any way or if any 

Company serial number has been removed or defaced. Product purchased from 

Company, but used on non-Company Products are excluded from this warranty.

Limitations:

To the maximum extent permitted by law except as expressly stated herein, there 

are no warranties, expressed or implied, by operation of law or otherwise, of the 

Product furnished under this Agreement. Seller disclaims any implied warranty of 

merchantability or fitness for a particular purpose. The sole remedy for liability of 

any kind shall be limited to the remedies provided in this warranty and shall in no 

event include any incidental, indirect, special or consequential damages or loss of 

use, revenue or profit. Should the company nevertheless be found liable for any 

damages, the total liability of the company shall be limited to the purchase price  

Confirmation of the defect shall require that reasonable proof of the defect be 

of the Product.

provided by Purchaser to Company or Company authorized agent, and may 

include that the Product or part be returned to Company for inspection at the 

Purchaser’s initial expense. If the Purchaser chooses to order a replacement part 

prior to the final determination of the warranty claim, Purchaser will be responsible 

for the cost of the replacement part and its shipping.  If the part is determined 

to be a valid warranty claim, the customer will be credited the amount of the 

replacement part and its shipping. Replacement parts for Products outside the 

United States will be shipped in the next authorized Dealer shipment unless 

Summary of Contents for Over-Center 24k60





























Reviews: