background image

 

Protect your boat from the harmful effects of the sun, wind and snow.

ACCESSORIES FOR MOST BASTA BOATLIFTS

CANOPIES

Centering Devices

These vertical reference guides

gently center your boat over the

lift and provide a constant

reference point for front/back

positioning.

Bow Stop

This adjustable bow stop assists

in proper placement of your boat

by gently stopping its forward motion.

Side Deck Brackets

One of the many advantages of

using a boat lift is the increased

accessability to your boat for

maintenance. These brackets

allow a side deck to be attached

to the existing boat lift or

canopy legs.

Load Guides 

Designed to make loading

your boat straight and true

amazingly easy - even in

cross winds and active water.

Light kit

Install these lights above or

below the water. They turn on

with your remote control key fob. 

Power Unit Support Bracket

Safely secure the power unit box

to a boatlift canopy leg or the side 

of your dock.

For additional information and images visit our web site at 

www.gobasta.com  

or contact Basta Marine at 

1-866-GOBASTA

 for a catalog

.

TM

Low profile silhouette

Sturdy and wind resistant

Attaches to a variety of lifts

Wide choice of colors

Durable Weblon

® vinyl top

Optional Sunbrella® tops

22, 24, 26, 30, 33, 39 foot lengths

10 and 12 foot widths

All aluminum design

Custom extrusions - no welds

Sol

ø™ 33 canopy

Basta 

Sol

ø

™ canopy features:

page 27

Summary of Contents for Over-Center 24k60





























Reviews: