Batavia BT-CDA001, Operating Instructions Manual

7

English

through a suitable piece of hose for 

handling.
Please keep in mind that the content of a 

drain is infectious and may contain caustic 

drain cleaners. Wearing safety glasses and 

a mouth or face protection is mandatory!

WARNING: 

If the device does not perform 

as outlined in this manual, turn to the Bata-

via customer service or to a competent 

professional.

8.  Work light

The work light 

(7)

 illuminates the working 

area during operation.
When the trigger switch 

(4)

 is pressed the 

work light 

(7)

 turn son. When the trigger 

switch is released the work light turns off 

after approximately five seconds.

9.  Cleaning and maintenance

WARNING: 

Remove the battery before car-

rying out any maintenance/cleaning of the 

tool.

9.1 

Cleaning

•  Clean the flexible shaft with warm water 

and some detergent and allow it to fully 

dry in extended condition. After drying 

lightly oil the flexible shaft.

•  Use only a moist cloth to clean the unit. 

Do not use aggressive chemicals which 

may dissolve plastic parts, or abrasives. 

Always keep the ventilation slots clean 

and free from obstructions.

•  Keep safety devices, ventilation open-

ings and the motor housing as free as 

possible from dirt and dust. Rub the 

electric power tool with a clean cloth or 

blow over it with low pressure com-

pressed air.

•  We recommend that you clean your 

electric power tool immediately after 

each use.

•  Clean the electric power tool regularly 

with a damp cloth and somewhat soft 

soap.

9.2 

Maintenance

There are no inner parts of the tool which 

need maintenance.

10. Technical data

No load speed . . . . . . . . . .0 – 560 min

-1

Dredging capacity .   .   .   .   .   .   . ø 19 – 50 mm
Length of flexible shaft . . . . . . . . . . 7 m
Working length.   .   .   .   .   .   .   .   .   .   .   .   .   .   6.8 m
Diameter of shaft / shaft head.   ø 7 / 12 mm
Product weight without battery . . . 3.46 kg
Product dimensions.   .   .   .   . 40 × 17 × 20 cm
Sound pressure level L

pA

  .   .   .   .   .   69.8 dB(A)

Uncertainty K

pA

.   .   .   .   .   .   .   .   .   .   .   .   .   .   . 3 dB

Sound power level L

WA

  . . . . . . 80.8 dB(A)

Uncertainty K

WA

 . . . . . . . . . . . . . . 3 dB

Hand arm vibration . . . . . . . . .  2.3 m/s

2

Uncertainty K.   .   .   .   .   .   .   .   .   .   .   .   .   .1.5 m/s

2

IP class . . . . . . . . . . . . . . . . . . . IP43

11. Disposal

 Do not dispose of electric power 

tools with domestic refuse.

The electric power tool is shipped in 

packaging to reduce transport damage. 

This packaging is a raw material and as 

such can either be reused or can be fed 

back into the raw material cycle. The elec-

tric power tool and its accessories are 

made from various materials such as met-

als and plastics. Take defective compo-

nents to a special refuse collection point. 

Ask about these at your specialist shop or 

local council. The product and the user 

manual may be subject to changes. Techni-

cal data may be changed without prior 

notice.

11.1 

Batteries

Think of the environment when disposing of 

batteries. Contact your local authorities to 

find out where your nearest disposal area is.
Do not dispose of batteries with domestic 

refuse.
Do not dispose of by burning, risk of 

explosion.