2.
PERSONAL PRECAUTIONS
Risk of explosive gases
2.1 Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. For this reason,
it is of utmost importance to follow the instructions.
2.2 To reduce the risk of a battery explosion, follow these instructions and those published by the battery manufacturer and the manufacturer of
any equipment used in the vicinity of the battery. Review the cautionary markings on these products and on the engine.
2.3 NEVER smoke or allow a spark or fl ame in the vicinity of a battery or engine.
2.4 Be extra cautious to reduce the risk of dropping a metal tool onto the battery. It might spark or short-circuit the battery or other electrical part
that may cause an explosion.
3.
PREPARING TO INSTALL
Risk of contact with battery acid. Battery acid is a highly corrosive sulfuric acid.
3.1 Consider having someone close enough by to come to help in case of an accident when working near a lead-acid battery.
3.2 Have plenty of fresh water and soap nearby in case battery acid contacts the skin, clothing or eyes.
3.3 Wear complete eye and body protection, including safety goggles and protective clothing. Avoid touching the eyes while working near the battery.
3.4 If battery acid contacts the skin or clothing, immediately wash the area with soap and water. If acid enters the eyes, immediately fl ood the
eyes with cold running water for at least 10 minutes and get medical attention right away.
3.5 Clean the battery terminals before installing the battery disconnect. During cleaning, keep airborne corrosion from coming into contact with the
eyes, nose and mouth. Use baking soda and water to neutralize the battery acid and help eliminate airborne corrosion. Do not touch the eyes,
nose or mouth.
4.
INSTALLATION
Battery Disconnect with LED indicator
Installation Accessories:
Battery Terminal Positive Post
Buzzer/Speaker Bolts
Reset Button
Remote x 2 PCS
(Key FOBs)
Risk of explosive gases
4.1 Ensure all accessories and ignition is turned off. The best way to ensure the ignition is not turned on or accidently turned on is to not have the keys
inside the starter switch.
4.2 Locate the battery and gain access.
4.3 Remove the NEGATIVE (NEG, N, -) cable from the car battery fi rst. This is intended to prevent sparking during the installation.
4.4 Remove the POSITIVE cable (POS, P, +) from the battery post of the vehicle.
4.5a For Top Post Battery Connection:
Connect the POSITIVE (BATT+) side of the Battery Life Preserver™ Automatic Battery Disconnect to the positive top
post of the vehicle battery using the included battery terminal. Be sure to tighten the bolts securely.
Final Assembly
4.5b For Side Post Battery Connection (GM Style): If the battery style is a side post style, it will require the purchase of the side post battery adapter
like the Battery Doctor #30300. Once the side post battery adapter is installed, connect the POSITIVE (BATT+) side of the Battery Life Preserver™
Automatic Battery Disconnect to the positive side terminal post of the vehicle battery using the included battery terminal. Be sure to tighten the bolts
securely.
Side Post Adapter
#30300
Final Assembly
4.6 Connect POSITIVE (POS, P, +) battery cable to the terminal marked (+CABLE) on the battery disconnect. Firmly attach it with the included Positive
Post and screws. Ensure it is tight and secure. Use the vehicle insulator cap to cover the connection for proper insulation on the battery terminal when
completed.
4.7 Reconnect the NEGATIVE (NEG, N, -) cable, which had been removed in 4.3 back to the negative post of the vehicle’s battery. Before tightening the
negative terminal, place the negative wire (black wire) of the battery disconnect to the negative terminal bolt and tighten securely.
4.8 Attach the buzzer/speaker. The buzzer/speaker plugs directly into the battery disconnect switch harness. Ensure the surface of the location is clean
before attempting to mount it. Pull off the double sided tape from the bottom of the Buzzer and attach it on to a secure place away from any moving
parts or any heat source of the engine. Always use wire ties to secure any loose cables.
4.9 The installation of the Battery Life Preserver™ Automatic Battery Disconnect is now complete. The main unit will show a Blue LED fl ashing if the unit
is operating properly. If the LED is fl ashing any other color or no color at all, verify all connections and repeat the above procedures if required. At
this stage the Battery Life Preserver™ Automatic Battery Disconnect can be used to prevent battery drain or with the remote control it can immobilize
the engine by cutting off battery power and prevent battery drain at the same time.
4.10 The Battery Life Preserver™ Automatic Battery Disconnect comes with a separate RESET button switch. This switch could be attached and installed
permanently or it can be left unattached and only used when needed. If the RESET switch is left unattached, make sure to keep it in a secure and
safe location.
5.
OPERATING INSTRUCTIONS
5.1
Activating the Battery Life Preserver™ Automatic Battery Disconnect using the remote control (Key FOBs)
5.1a To disconnect the vehicle from the battery completely, press the button on the remote control. This will completely disconnect the
battery, cutting off all power to the vehicle. This will erase any memory presets and clock when using this function.
5.1b To use the Battery Life Preserver™ disconnect to monitor the battery and disconnect the power once the battery reaches 12.0V, then do not
press any buttons on the remote. Once the engine is shut off, the battery disconnect will automatically switch to monitoring mode. When
the battery reaches 12.0V for 30 seconds or more, the unit will automatically disconnect the power from the vehicle saving enough battery
starting power.
5.2
Deactivating the Battery Life Preserver™ Automatic Battery Disconnect (to turn off the anti-theft function)
5.2a Press
the button on the remote control to deactivate the Battery Life Preserver™ Automatic Battery Disconnect anti-theft function. This
will reconnect the battery.
5.2b When
the button is pressed, two short acoustic 110 dB “Beeps” will sound, the blue LED indicator on the remote control will light up
and the LED color on the main unit will change to blue, to indicate that the battery has been reconnected.
Please note, when it is installed, the Battery Life Preserver™ Automatic Battery Disconnect automatically begins to monitor the battery. If using
the remote to disconnect the battery, please hold the remote button for a few seconds. The few seconds delay on the remote button is a safety
feature, to prevent accidental pressing of the remote button to disconnect the battery.
NOTE : If the battery is disconnected using the remote control (key FOBs), then it can ONLY be reconnected by using the remote control again.
