background image

PNEUMATIC ZEUS mod. 2009 

page 10 

January 2009 

 
17.

 

WORKING CYCLE 

 

After having started the boiler 

(when the boiler is under pressure the “steam” icon will 

turn off), carried out all the adjustments and chosen the program,  ZEUS is ready for 

use.  
To  start  the  automatic  cycle,  just  insert  the  sleeves  into  the  clamps.  ZEUS  will 

automatically tighten them. Now press the pedal 

(fig. 1)

. This way  the arms get in 

traction  and  the  steam  cycle  is  activated,  then  the  air-steam  cycle  and,  eventually, 

the hot air cycle. The various phases and timings are shown on the display. Once the 

working cycle has finished, the  clamps open and the arms close down; the operator 
can start another cycle. 

N.B. The working cycle does not start if the temperature of the super-heater 

is  below  120°C  and/or  if  both  the 

clamps  have  not  closed  themselves 

correctly. If the clamps are not necessary, follow instruction as per chapter 

Deactivation and activation of arms and clamps

.  

 

Note: 
1. it is possible to interrupt the working cycle anytime by pressing the pedal; 

2. each time you change the type of fabric to iron, and especially when changing from 

heavy fabrics to delicate ones, just repeat the settings at points 

13 

and 

14

3. it is not possible to change the timings of the various phases during the working cycle. 

 
 

18.

 

 DEACTIVATION AND ACTIVATION OF ARMS AND CLAMPS 

 

Whenever y

ou don’t need arms and 

clamps, you can deactivate them and go on with 

the normal ironing cycle. 

 

In order to deactivate the clamps just 
follow these points: 

1.

 

Press  the  “

clamps 

deactivation” 

key (the led will turn on) 

2.

 

Turn  the  air  closing  valve  to 

position 

OFF 

(no clamps)

 (fig. 6).

 

 

In order to reactivate the  clamps just 
follow these points: 

1.

 

Press  the  “

clamps 

deactivation” 

key (the led will turn off) 

2.

 

Turn  the  air  closing  valve  to 

position 

ON 

(with  clamps) 

(fig. 

6).

 

 

 

 

WARNING! For a good functioning of the ironing cycle remember to press the 
key and turn the valve. 

 
 

 

 
 

 
 

ESC

ADJUSTME NT
OF GENERAL
PRE SSURE

LUBRICATOR

MANOMETE R

AIR INLET

"CLAMPS DEACTIVATION"
KEY

ON

OFF 

(WITHOUT CLAMPS)

(WITH CLAMPS)

AIR CLOSING
VALVE

 

Fig. 6 

Summary of Contents for PNEUMATIC ZEUS/A
















Reviews: