background image

PNEUMATIC ZEUS mod. 2009 

page 9 

January 2009 

16.

 

USE OF MEMORIZED IRONING PROGRAMS 

 

By pushing the key shown on the left it is possible to choose between  
the 20 stored ironing programs.  The UP, DOWN keys are used to scroll 

the  pre-stored  ironing  programs  as  well  as  a  manual  personalized 

program. 

It  is  possible  to  immediately  skip  to  the  “

OPERATOR

” 

program by pressing the SET key and then ESC  

 
 

 

 

The 

CUSTOMER

  program  allows  the  operator 

to  create  and  store  a  “working  cycle” 

according to the timings desired. Choose the manual program, wait for 5 seconds until 

the timings of the various phases appear and then set the desired values, which will 

be stored automatically.  
The other pre-stored  programs may be modified by the operator, but when voltage is 

cut off or when other programs are used, the modifications will be cancelled and the 
values stored by the manufacturer will be set. 

According  to  the  ironing  program  chosen  the  suggested  air  adjustment  will  be 

displayed (Fig.1). Example: 

KINTTED LADIES DRESS air adj 1 

N.B. the setting of the super-

heater’s temperature does n

ot depend on the program 

chosen, therefore the latest setting remains stored. 

 

SET

 

UP

DOWN

°C

 

IRONING PROGRAM

 

SUGGESTED 

AIR 

ADJUSTMENT 

STEAM 

AIR/STEAM 

AIR 

SECONDS 

SECONDS 

SECONDS 

CUSTOMER 

 

May be set 

by operator  

May be set 

by operator  

May be set 

by operator 

1° 

CHILDRENS SWEATSHIRT 

2° 

MENS SWEATSHIRT 

3° 

CHILDRENS SMOCK 

4° T

-SHIRT 

10 

5° 

DRY SHIRT 

10 

6° SHORT

-SLEEVED SHIRT 

7° 

WORKING SHIRT 

8° LIGHT JACKET

 

9° HEAVY JACKET

 

10 

10° LEATHER JACKET 

 

10 

11° COAT

 

10 

12° MENS SPORTS JACKET

 

10 

13° 

LIGHT LADIES DRESS 

14° KNITTED LADIES DRESS

 

10 

15° DAMP SHIRT 1°

 

15 

10 

45 

16° DAMP/WET SHIRT 2°

 

20 

10 

60 

17° WASHED OUT JACKET 

 

10 

18° JEANS JACKET

 

10 

10 

10 

19° LINEN JACKET 

 

15 

10 

10 

20° HEAVY SHIRT

 

12 

10 

Summary of Contents for PNEUMATIC ZEUS/A
















Reviews: