Bauer 1621e-b Owner'S Manual Download

Page: 6 / 16

Page 6

For technical questions, please call 1-888-866-5797.

Item 63445

AFET

Op
ERA

TION

AINTENAN

ETU

Setup - Before Use:

Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION:
Turn the power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.

Note:

For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Functions

power

Switch

Infeed

Table

Outfeed

Table

Depth

Adjustment

Handle

Thermal circuit

Breaker Reset

Dust

chute

Depth

Adjustment

Scale

carrying

Handle

carrying

Handle

cutterhead

(not visible)

Rollers

yellow

Key

Off

Locked

power Switch positions

Figure A

Summary of Contents for 1621e-b

















Search results

Summary of Contents for 1621e-b

Reviews:

Related manuals for 1621e-b

Brands by name

Popular brands

Bauer 1621e-b, Owner'S Manual

Search results

Summary of Contents for 1621e-b

Reviews:

Related manuals for 1621e-b

Brands by name

Popular brands