Bauer 20V Hypermax Lithium 1895C-B Owner'S Manual Download

Page: 1 / 16

Visit our website at: http://www.harborfreight.com

Email our technical support at: productsupport@harborfreight.com

Owner’s Manual & Safety Instructions

Save This Manual

Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

-tc

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

2018 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Summary of Contents for 20V Hypermax Lithium 1895C-B

















Search results

Summary of Contents for 20V Hypermax Lithium 1895C-B

Reviews:

Related manuals for 20V Hypermax Lithium 1895C-B

Brands by name

Popular brands

Bauer 20V Hypermax Lithium 1895C-B, Owner'S Manual

Search results

Summary of Contents for 20V Hypermax Lithium 1895C-B

Reviews:

Related manuals for 20V Hypermax Lithium 1895C-B

Brands by name

Popular brands