GB-4
Electric telescoping hedge trimmer
Technical data
Model
GHTI 60 Gardol
Operating voltage V~
230
Nominal frequency Hz 50
Nominal consumption W
600
Cutting motion rpm
3300
Maximum cutting length mm
514
Maximum cutting diameter mm 20
Angle at which the motor can be set 0° to 120°
Tool length cm approx. 195 - 240
Weight without the cable kg 4,1
Sound power level L
WA
dB (A) 104
Noise Pressure level L
pA
(EN ISO 10517)
dB (A) 89
K= 3,0 dB(A)
Vibration
(EN ISO 10517)
m/s
2
3,0
K= 1,5 m/s
2
Protection class II/DIN EN 60745/VDE 0740
The specified vibration emissions value is measured in accordance with EN 60745. This can be used for any other
hedge trimmer with the same design and type of power supply.
The specified vibration emissions value limits the working time. Stop working if you notice a tingling sensation or a
discolouration (white) of the fingers.
WARNING:
When in operation, the tool‘s actual vibration emissions value can deviate from the specified value de
-
pending on how the tool is used, as in the following examples or because it is used in another way:
- How the tool is being used and which materials are being cut.
- The tool is well maintained and in good working order. The correct accessories are being used and care has been
taken to make sure they are sharp and in good working order.
- How secure the hand grip is and whether anti-vibration accessories are being used.
-
Whether the tool is being used in accordance with its design and as specified in these instructions.
- The tool can cause hand-arm vibration syndrome symptoms if it is not used properly.
WARNING:
To make sure, an assessment should be made of the strain exerted when the tool is in use, for example
when the tool is switched off or is idling. This will make it possible to significantly reduce the strain exerted during the
entire time the tool is in use.
Minimise your risks if the tool vibrates.
Take care of the tool as specified in these instructions and make sure the tool is properly lubricated (if necessary).
If the temperature is 10°C or less, do not use the tools. Prepare a work schedule so that work is distributed over
several days when using tools that exert high vibrations.
A certain degree of noise from this device is unavoidable. Perform noise-intensive work at times when this is permit-
ted and at times intended for this type of work. Where applicable, observe quiet times and limit working time to the
absolute minimum. You and other persons in the area where the trimmer is being used should wear suitable hearing
protection
.
Noise emission information in accordance with the German Product Safety Act (GPSG) and the EC Machine Direc-
tive: the noise pressure level at the place of work can exceed 80 dB(A). In such cases the operator will require noise
protection (e.g. wearing of ear protectors).
Attention: Noise protection!
Please observe the local regulations when operating your device.
Summary of Contents for GHTI 60 Gardol
