32
5.7 Setup-Menü des Systemarbeitsmodus
Arbeitsmodus
zuerst verkaufe: In diesem Modus kann der Hybrid-Wech-
selrichter überschüssige Energie, die von den Solarmodu-
len erzeugt wird, an das Netz zurückverkaufen. Wenn die
Nutzungszeit aktiv ist, kann auch die Batterieenergie ins
Netz verkauft werden.
Die PV-Energie wird zur Versorgung der Last und zum Aufla-
den der Batterie verwendet, und die überschüssige Energie
fließt dann ins Netz. Die Priorität der Stromquelle für die
Last ist wie folgt:
1. Solarmodule.
2. Netz.
3. Batterien (bis zum Erreichen der programmierbaren
%-Entladung)
Kein Export - zur Last :
Der Hybrid-Wechselrichter versorgt nur die angeschlossene Ersatzlast mit Strom. Der Hybrid Wechselrichter liefert
weder Strom an die Hauslast noch verkauft er Strom an das Netz. Der eingebaute Stromwandler erkennt Strom,
der ins Netz zurückfließt, und reduziert die Leistung des Wechselrichters nur, um die lokale Last zu versorgen und
die Batterie zu laden.
Kein Export zum Stromwandler:
Der Hybrid-Wechselrichter versorgt nicht nur die angeschlossene Backup-Last, sondern auch die angeschlossene
Haushaltslast mit Strom. Wenn der PV-Strom und der Strom aus der Batterie nicht ausreichen, nimmt er die Energie
aus dem Netz als Ergänzung. Der Hybrid-Wechselrichter gibt keinen Strom an das Netz ab. In diesem Modus wird
ein Stromwandler benötigt. Die Installationsmethode für den Stromwandler finden Sie in Kapitel 3.6 Stromwand-
leranschluss. Der externe Stromwandler erkennt, dass Energie ins Netz zurückfließt und reduziert die Leistung des
Wechselrichters nur, um die lokale Last, die Batterie und die Haushalte zu versorgen.
- 33 -
Recommended ba�ery se�ngs
Battery Type
AGM (or PCC)
Absorption Stage
14.2v (57.6v)
13.4v (53.6v)
Float Stage
Torque value
(every 30 days 3hr )
14.2v(57.6v)
Gel
14.1v (56.4v)
13.5v (54.0v)
Wet
14.7v (59.0v)
13.7v (55.0v)
14.7v(59.0v)
Lithium
Follow its BMS voltage parameters
5.7 System Work Mode Setup Menu
Zero Export To Load
Max Solar Power
Zero Export To CT
Max Sell Power
Energy pattern
BattFirst
LoadFirst
System Work Mode
Solar Sell
Solar Sell
12000
12000
Power
8000
Zero-export Power
20
Selling First
Work
Mode1
Grid Peak Shaving
Work Mode
Selling First:
This Mode allows hybrid inverter to sell
back any excess power produced by the solar panels to
the grid. If �me of use is ac�ve, the ba�ery energy also
can be sold into grid.
The PV energy will be used to power the load and charge
the ba�ery and then excess energy will flow to grid.
Power source priority for the load is as follows:
1. Solar Panels.
2. Grid.
3. Ba�eries (un�l programable % discharge is reached).
Zero Export To Load:
Hybrid inverter will only provide power to the backup load connected. The hybrid
inverter will neither provide power to the home load nor sell power to grid. The built-in CT will detect
power flowing back to the grid and will reduce the power of the inverter only to supply the local load and
charge the ba�ery.
Zero Export To CT:
Hybrid inverter will not only provide power to the backup load connected but also give
power to the home load connected. If PV power and ba�ery power is insufficient, it will take grid energy
as supplement. The hybrid inverter will not sell power to grid. In this mode, a CT is needed. The installa�on
method of the CT please refer to chapter 3.6 CT Connec�on. The external CT will detect power flowing back
to the grid and will reduce the power of the inverter only to supply the local load, charge ba�ery and home
load.
Grid
Backup Load
On-Grid Home Load
Battery
Solar
Grid
Backup Load
On-Grid Home Load
Battery
Solar
CT
- 33 -
Recommended ba�ery se�ngs
Battery Type
AGM (or PCC)
Absorption Stage
14.2v (57.6v)
13.4v (53.6v)
Float Stage
Torque value
(every 30 days 3hr )
14.2v(57.6v)
Gel
14.1v (56.4v)
13.5v (54.0v)
Wet
14.7v (59.0v)
13.7v (55.0v)
14.7v(59.0v)
Lithium
Follow its BMS voltage parameters
5.7 System Work Mode Setup Menu
Zero Export To Load
Max Solar Power
Zero Export To CT
Max Sell Power
Energy pattern
BattFirst
LoadFirst
System Work Mode
Solar Sell
Solar Sell
12000
12000
Power
8000
Zero-export Power
20
Selling First
Work
Mode1
Grid Peak Shaving
Work Mode
Selling First:
This Mode allows hybrid inverter to sell
back any excess power produced by the solar panels to
the grid. If �me of use is ac�ve, the ba�ery energy also
can be sold into grid.
The PV energy will be used to power the load and charge
the ba�ery and then excess energy will flow to grid.
Power source priority for the load is as follows:
1. Solar Panels.
2. Grid.
3. Ba�eries (un�l programable % discharge is reached).
Zero Export To Load:
Hybrid inverter will only provide power to the backup load connected. The hybrid
inverter will neither provide power to the home load nor sell power to grid. The built-in CT will detect
power flowing back to the grid and will reduce the power of the inverter only to supply the local load and
charge the ba�ery.
Zero Export To CT:
Hybrid inverter will not only provide power to the backup load connected but also give
power to the home load connected. If PV power and ba�ery power is insufficient, it will take grid energy
as supplement. The hybrid inverter will not sell power to grid. In this mode, a CT is needed. The installa�on
method of the CT please refer to chapter 3.6 CT Connec�on. The external CT will detect power flowing back
to the grid and will reduce the power of the inverter only to supply the local load, charge ba�ery and home
load.
Grid
Backup Load
On-Grid Home Load
Battery
Solar
Grid
Backup Load
On-Grid Home Load
Battery
Solar
CT
- 33 -
Recommended ba�ery se�ngs
Battery Type
AGM (or PCC)
Absorption Stage
14.2v (57.6v)
13.4v (53.6v)
Float Stage
Torque value
(every 30 days 3hr )
14.2v(57.6v)
Gel
14.1v (56.4v)
13.5v (54.0v)
Wet
14.7v (59.0v)
13.7v (55.0v)
14.7v(59.0v)
Lithium
Follow its BMS voltage parameters
5.7 System Work Mode Setup Menu
Zero Export To Load
Max Solar Power
Zero Export To CT
Max Sell Power
Energy pattern
BattFirst
LoadFirst
System Work Mode
Solar Sell
Solar Sell
12000
12000
Power
8000
Zero-export Power
20
Selling First
Work
Mode1
Grid Peak Shaving
Work Mode
Selling First:
This Mode allows hybrid inverter to sell
back any excess power produced by the solar panels to
the grid. If �me of use is ac�ve, the ba�ery energy also
can be sold into grid.
The PV energy will be used to power the load and charge
the ba�ery and then excess energy will flow to grid.
Power source priority for the load is as follows:
1. Solar Panels.
2. Grid.
3. Ba�eries (un�l programable % discharge is reached).
Zero Export To Load:
Hybrid inverter will only provide power to the backup load connected. The hybrid
inverter will neither provide power to the home load nor sell power to grid. The built-in CT will detect
power flowing back to the grid and will reduce the power of the inverter only to supply the local load and
charge the ba�ery.
Zero Export To CT:
Hybrid inverter will not only provide power to the backup load connected but also give
power to the home load connected. If PV power and ba�ery power is insufficient, it will take grid energy
as supplement. The hybrid inverter will not sell power to grid. In this mode, a CT is needed. The installa�on
method of the CT please refer to chapter 3.6 CT Connec�on. The external CT will detect power flowing back
to the grid and will reduce the power of the inverter only to supply the local load, charge ba�ery and home
load.
Grid
Backup Load
On-Grid Home Load
Battery
Solar
Grid
Backup Load
On-Grid Home Load
Battery
Solar
CT
