background image


 

SAFETY INSTRUCTIONS 

 
This machine demands skilled operation therefore, 

you must read this operator’s manual 

before connecting the machine to the tractor

.  Even though you may have owned or operated 

similar equipment, you should read through the safety and maintenance procedures 
thoroughly.  

This concerns your safety.

 

 
The Bauman Drop Spreader should only be operated by one person.  The operator should 
ensure that no one is close to the area where the machine is in use.  Do not let others operate 
the machine unless you are certain that they have the necessary knowledge to operate the 
machine safely and correctly. 
 
The following precautions should be read and understood before operation of the machine: 

 

Activate the tractor’s parking brake and stop the tractor’s engine 

before: 

 

Unclogging material jams; 

 

Lubricating the machine; 

 

Cleaning the machine; 

 

Disassembling any part of the machine; 

 

Adjusting, repairing, or maintaining the machine. 

 

Lower the machine to the ground when parked. 

 

Disconnect power before servicing. 

 

Do not work underneath an elevated unit until it has been secured mechanically or with 
stop wedges. 

 

Do not start or operate the tractor until bystanders are clear of the machine. 

 

Check to make sure that all tools have been removed from the machine before starting 
the tractor. 

 

Check that all safety shields and grills are in place and secured. 

 

Do not operate the machine while wearing loose garments. 

 

Use statutory vehicle lights and safety markings when operating the spreader on public 
roads or when driving in the dark. 

 

Hearing protection is recommended, especially if the machine is in use over a long 
period of time. 

 

Before lifting or lowering the spreader, ensure there is no one in the vicinity of the 
machine.  Do not stand between the tractor and the spreader during attachment and 
detachment. 

 

The machine has been manufactured strictly for the intended use as a drop spreader.  
Do not use the machine for any other purpose. 

 

Be considerate of people, property and animals near the machine.  Maintain a distance 
of at least 10 meters from obstacles while operating from the machine. 
 
 
 

Summary of Contents for 440E

























Reviews: